Jump to content
SAU Community

Recommended Posts

nah didnt change everyday driving, or even just planting it.. as it always went to 100%

but tonight i shall be swinging around for more testing.. i have something else i wanna try..

but i have noticed that down low the AFR's have changed down low on stall.. obviously now its getting much more air and not tuned for it, and where there wasnt boost before, there now is.. i guess the MAP sensor is helping but yeh.. i may need Cihan to do a quick road tune just for bottom end WOT.

when you get yours in today let me know what you think??

plus i think that it would only make a good difference with a highstall.. as you said yours is now hitting stall so you wouldve seen the bigger difference. the extra 5psi or so helps.

nah didnt change everyday driving, or even just planting it.. as it always went to 100%

but tonight i shall be swinging around for more testing.. i have something else i wanna try..

but i have noticed that down low the AFR's have changed down low on stall.. obviously now its getting much more air and not tuned for it, and where there wasnt boost before, there now is.. i guess the MAP sensor is helping but yeh.. i may need Cihan to do a quick road tune just for bottom end WOT.

when you get yours in today let me know what you think??

Ok, makes sense. At least now he can tune it properly as the damn throttle opens now, a little lean off boost should be ok and help it spool I guess. Better call Cihan later.

the quick test i did in the city, the car went to 45% then to 100% for me. the 45% was probably a delay in the screen update or something.

ill do it again this afternoon on the way home in the back streets. at least the car will be well and truly warm by then

the quick test i did in the city, the car went to 45% then to 100% for me. the 45% was probably a delay in the screen update or something.

ill do it again this afternoon on the way home in the back streets. at least the car will be well and truly warm by then

you need to fully press the brake in. and hold the accel for a few seconds.. it should sit at 40-45%.. if you release the brake with the accel to the floor you will see 100%.

It definitely feel its much more responsive and the hesitation it had sometimes coming out of corners is gone. There must be a delay on that wire I cut to stop the throttle opening. Bloody Mr Nissan.

It definitely feel its much more responsive and the hesitation it had sometimes coming out of corners is gone. There must be a delay on that wire I cut to stop the throttle opening. Bloody Mr Nissan.

thinking of this.. i actually have slightly better off the line take of.. as in the response to when you slam the accelerator is much different now..

lol this morning i managed to get the wheels spinning again, and they're pirelllliiiiiiss lol

fun lol.

im gonna put mine hidden in the dvd area.. eventually

When you think about it, there's probably only 2 possible reasons to even put in a switch.

1) The ECU eventually throws a code (unlikely given how many km's you guys have done since cutting the wire)

2) You lend your car to someone & you think they may try to launch it from standstill, & they can't drive, & it's wet, & etc

In which case you wouldn't lend them the car, right? I put the switch in so I could easily compare before & after & before & after again, & after & after....lol. But I wasn't hooning & there wasn't a tunnel anywhere near here :whistling:.

The only difference I could pick driving around town was that there was slightly better acceleration if you really had to cross the intersection before getting t-boned, & you'd been stopped with your foot on the brake.

The launch is certainly better, but not as noticeable as my experiments a few weeks ago. Obviously there were other factors at play then, but not enough to make me want to pursue that testing now that a free mod seems to fix the low end restriction.

What's funny was the conclusions we had come to previously that seem inaccurate now pinch.gif .

ok ill perform this mod one day this year........ damn being married into an italian family is hard work. something on ALL the time lol

anyway, i bet the nismo ECU gets the cams on faster, so lets go with that so craig and i still have something over you all :P

anyway, i bet the nismo ECU gets the cams on faster, so lets go with that so craig and i still have something over you all :P

Mate, I hope you do get something extra for having a Nismo ECU :blink: . You'd have to be annoyed at paying money for nothing more than you could get by cutting a wire.

Surely Nismo don't just disable that input and sell it for $800 or whatever?? That would be a huge scam if that was the case lol.

LOL. :nyaanyaa:

Anyway, I decided not to put a switch for now as it seems to be fine. At worst you would only have to turn the car off for a second to reset it anyway.

The high stall converter is the key here though, I could never get it onto stall before with the highflow so it would always be a slug off the line, even worse than stock because I had no push from the converter (because it wasn't coupling yet) Now I can so it will make living with the GTX turbo much more bearable.

Mate, I hope you do get something extra for having a Nismo ECU :blink: . You'd have to be annoyed at paying money for nothing more than you could get by cutting a wire.

Surely Nismo don't just disable that input and sell it for $800 or whatever?? That would be a huge scam if that was the case lol.

youd hope thats not all they did!! haha

but no it was a full tune as well, also dual maps (if you want that). who knows about the cam advance, Scotty is there any way to tell? does something go high or low that i can chuck a meter on?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...