Jump to content
SAU Community

Recommended Posts

well it just seems like you are making it a big deal that i am chooing to want to supercharge my skyline, and it seems like you dont like the fact that i am "stepping out of the square" and doing something different.

and if i want to go wank facter then i will.

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

you can do whatever the hell you like, i'm not going to lose any sleep over your choice.

i was asking why you'd go with a blower that offers very much the same characteristics as a turbo, except at a higher price..

if i was to go a supercharger, i'd be aiming for something with no lag, and a very broad power curve, rather than a peaky figure that a turbo can deliver.

ok so let me get this straight,

you are spending more money than the entire car is worth,

to do something "different"

for results that are far less than anything conventional (tried and tested that works and is good)

and you expect everybody to post and say

"yeah awesome idea"

"i like how you have chosen to spend more money for less gains"

not everyones going to agree and say different is better

you must know that, so no point getting all annoyed at everybody who tells you so.

unique400x300.jpg

most people who spend 100,000 on a car are buying something like an R35 GTR, or are pulling off a tax scam (and don't tell me half the big money autosalon entries aren't tax writeoffs). you're getting into debt to build this. just seems like you're making emotional decisions instead of rational ones that's all, and I'm sure half the people posting "against" you are trying to point that out.

everyone loves an innovator, but innovation at what cost?

most people who spend 100,000 on a car are buying something like an R35 GTR, or are pulling off a tax scam (and don't tell me half the big money autosalon entries aren't tax writeoffs). you're getting into debt to build this. just seems like you're making emotional decisions instead of rational ones that's all, and I'm sure half the people posting "against" you are trying to point that out.

everyone loves an innovator, but innovation at what cost?

dont argue with woman logic

in any case... if you want some pointers from guys who've done it before, have a good read of this thread:

http://www.driftworks.com/forum/drift-car-...rift-car-8.html

The build itself is fuckin epic.

They used an RB30 engine (aus spec RB30 block with RB26 head) and a Kenne Bell 2.8H twin scroll (which IMHO is the sweetest sounding supercharger when mated to a big Ford 5.4L).

http://www.kennebell.net/superchargers/for...elby/Shelby.htm

There's also a R34 drag car in NZ that runs 660hpish on a Procharger F1R Supercharger, again bolted to an RB30.

Well there are two main problems with a vortech supercharger the first is lag, just like a turbo and the other is the considerable mechanical effort required to turn the supercharger.

Advantages are that they are compact, the boost increases at higher rpm so as to maximise the power adding potential, and they are incredibly efficient compared to roots and screw type superchargers. They are also quite cheap compared to a roots or screw.

If it was my money I would be doing something totally different, but its not its hers and I am intruiged by this whole project honestly because its not what i would do.

Cara, he did ask a simple question and its quite an easy one to answer - retract the claws.

EDIT: Also I just read your comment about there not being much lag due to tune. The only way to reduce lag on a supercharger is to increase rotational speed - i.e. increase engine rpm. Its not a turbo, tune won't help.

Edited by R33_Dude

dude, i think i might just add, that the supercharger i am using is a centrifugal supercharger.

and no, lag is not an issue, because the supercharger dosent have to spool up like a turbo! and the fact that they are driven by the crankshaft,

and the root and screw type superchargers, are two totally different types of blower to the one i am getting.

Let people be, everyone no matter what do things people don't agree with or understand.

Like Cara building her car, I'm building a ford corsair.. Yes a ford corsair, it will be running a nissan awd system, now many of these do you think there is, considering there is no such thing in the world asaik of an awd ford coresair? Now I know I can spend a shitload less and have something better in everyone elses eyes but I'm building this for me and you would not believe the amount of people who have tried to stop me saying it is stupid for the amount i will be spending.

Project cars are project cars they always cost a shitload and things always get blown way out of proportion, that's what makes them so fun :) haha

Edited by Eug
thread clean up

Well to start off...

There is nothing about you doing this that makes sense....but thats kinda cool :)

Your money could be spent better elsewhere, but it were going to race it then I am sure you would.

You obviously have researched this and are keen on doing it, so I say good luck to you.

You WILL have problems and plenty will go wrong....there is no doubt, i had problems going from an rb20 to an rb25 and still sorting out issues

It WILL cost more then what you planned, it always does no matter how in depth you have gone into it.

You WILL get better bang for bucks from a turbo...but you aren't after that.

Did I mention good luck with it and that it is a crazy idea!!

Will be interesting to see in the flesh when it's done...as long as you don't polish everything under the bonnet or cover everything in carbon fibre.

Again good luck and keeps us posted or blogged, should be good to see what you can fit into the engine bay of an R34.

Cheers Ro. :thumbsup:

hey dude thanks

i wont be polishing or carbon fibreing everything under the bonnet lol

the piping will be made of the same material that my intercooler piping is made up (aluminium or some shizz?lol) so that will prob be the real bling bling part of it!

Good luck with the charged project it is great to see something different, we do a lot of chargers here on big displacement v8's and i love them to death.

Honestley im not a big fan of them on smaller engines as they need to be revved hard ( see boost graph, ive included a typical charged graph too, overlayed with a turbo curve.) to gain the most benefits the power is way too linear (like a 45 degree ) turbos tend to make more much more mid and similar top end. Hopefully the builder can adress this and im sure he / she will.

In my experience the little bit of bottom end gain is not worth the mid range loss on smaller capacity engines.

Here are some nice charged cars weve had in lately.

post-34927-1240920831_thumb.jpg

post-34927-1240921447_thumb.jpg

post-34927-1240921577_thumb.jpg

post-34927-1240922077_thumb.jpg

post-34927-1240922239_thumb.jpg

Edited by URAS
dude, i think i might just add, that the supercharger i am using is a centrifugal supercharger.

and no, lag is not an issue, because the supercharger dosent have to spool up like a turbo! and the fact that they are driven by the crankshaft,

and the root and screw type superchargers, are two totally different types of blower to the one i am getting.

I realise they are different. I was pointing out to someone who posted earlier on as to why you would use a centrifugal supercharger.

I will say this, and I will say this clearly: Centrifugal superchargers experience lag. On small capacity applications they only reach usable boost (psi gained minus rotational force required) at around three thousand rpm.

Here are some references to prove what I am saying:

"Due to its design and lack of low-RPM boost it is often employed on near-standard compression engines" - http://en.wikipedia.org/wiki/Centrifugal_supercharger

"One of the disadvantages of the centrifugal supercharger is that the centrifugal compressor works best over a rather small RPM range" - Sport Compact Car Engine & Driveline Handbook (You would have to buy this or look it up on google books. Page 27, near the bottom.)

It is also in my engineering book on superchargers, I would scan it up for you but alas I have no scanner at the moment and the book is packed away with about a million others. It says something along the lines of centrifugal superchargers building boost with RPM, however lag conditions are created at low RPM, hence why they can be used on mechanically standard engines as the volumetric efficiency of an engine falls when RPM rises. Thus the supercharger compensates by increasing air flow at higher RPM improving power, response and torque throughout the upper mid range and top end.

Essentially a supercharger isn't a supercharger. Screw superchargers produce constant boost. Roots superchargers produce boost down low but seem to lose steam at the top end (quite inefficient too). Centrifugal suffers at the bottem end but the trade off is top end.

EDIT: I have another quote from Sports Compact Car Engine and Driveline Handbook: "Thus even though the centrifugal supercharger is connected to the crankshaft, it still suffers from power lag, a non-linear power delivery sometimes worse than that of even a fairly aggressive, large sized turbo."

HOWEVER

"Centrifugal superchargers are more thermally efficient than the roots blower"

Just as I have been saying all along. But no I can't be right.

 

Edited by R33_Dude
of course you can't, you have a differing opinion!!!

So how is what she is doing wrong??

Yes there are cheaper ways of getting power and better gains from having a turbo charger...but she is not after that.

So why pursue on the idea?

You and I may not do it cause there are the better ways.

She wants something different.

I am sure there a better trackable cars then your R31...but you like it.

So how is what she is doing wrong??

Yes there are cheaper ways of getting power and better gains from having a turbo charger...but she is not after that.

So why pursue on the idea?

You and I may not do it cause there are the better ways.

She wants something different.

I am sure there a better trackable cars then your R31...but you like it.

Buddy.... Did you have a look at that fork picture on page 2 of the thread?

If you did, have another look, it will explain EVERYTHING.

They aren't saying what she's doing is wrong, they are saying that you can have something more powerful, more drivable, with LESS cost.

People are usually rational i.e. comparing projects with cost vs benefit analysis.

This idea appears irrational to me.

Spending that much money merely to have a supercharger.... WA WA WI WA!

You've got my complete respect now...........

Once your car is done, can we meet up and get freaky in the back seat?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
×
×
  • Create New...