Jump to content
SAU Community

Recommended Posts

Basically what the above person mentioned.....

Check condition of gear knob, steering wheel, side bolster on the drivers side seat, wear on the pedals, check alignment of km digits.

Take it for a drive, listen for any knocks in the suspension or a rough idle. Check for oil leaks etc.

Could someone please explain why it is so common for imported cars to have excessively worn (basically no leather left on them) steering wheels? Do Japanese drive with sandpaper gloves or something? Or is it from something else? Most cars you see here could have done over 200,000kms and the wheel isn't worn.

Originally posted by dan_the_man

apparently Japanese men who smoke, sit in traffic jams and pick at the steering wheel with their nails... frustration of some sort.

Thats why its only on the top half of the wheel

Well look at it like this...

If we exported our old VN Commodores and EA Falcons to Japan, what would they say about us?

The same thing we say about them!

ie. young hoon type who smoke more than just cigarettes, big type sound systems and wear on knobs, wheels and pedals from general bad driving. If you wear rings you wear out the steering wheel.

T.

Originally posted by jabtronic

Could someone please explain why it is so common for imported cars to have excessively worn (basically no leather left on them) steering wheels? Do Japanese drive with sandpaper gloves or something? Or is it from something else? Most cars you see here could have done over 200,000kms and the wheel isn't worn.

I've heard that it's because a lot of Japanese are fond of the bling bling and wear lots of gold rings which may cause excessive wear on the wheel.

There are exceptions to the rule though, mine was in excellent condition when I got it, and is virtually the same now (I don't wear any rings or pick at the wheel with my fingernails).

You might be able to see some small wear on the right on mine in this pic, this is from where the previous owner attached the "overboost" button for the boost controller. I never used it so I removed it.

Japan has one of the highest % of smoking population in the world.

"I've heard that it's because a lot of Japanese are fond of the bling bling and wear lots of gold rings which may cause excessive wear on the wheel. "

False. Many men don't even wear wedding rings.

I've walked through many, many japanese car yards and have consistantly seen cars with low kms. Wound-back odos are definitely a fact of life, but I have a feeling that happens far less than people think - particularly with high-end performance cars (though I wouldn't say a GTST fits under that category).

Originally posted by DaiOni

"I've heard that it's because a lot of Japanese are fond of the bling bling and wear lots of gold rings which may cause excessive wear on the wheel. "

False.  Many men don't even wear wedding rings.

So they're all just a bunch of neurotic steering wheel pickers then?

dunno, my s. wheel and g. knob were both fairly worn and my car only had approx. 43k km on the clock (logs to back it up). I simply replaced them with momo and feed items anyway

sweaty hands maybe? though they often claim that they don't sweat as much as gaijin...

i used to think that the condition/wear of the interior/exterior items would be a sure indication of the 'true' age of the vehicle. I remember when shopping around for a 180SX a year ago....saw one on sale for around 40-ish Kms on the odo....but the interior and engine bay condition was just shocking....dusty, faded interior panels...worn pads...etc etc...

Now with my 96 S2, it came with 36ks on the odo, immediately i thought "yeah right"....but i was amazed at the condition of the interior as well as the engine compartment....then again parts could've been replaced etc etc....so i didn't really care....besides it went really well...

Took it to 2 seperate workshops to get some servicing done and mods....and both(without me asking) commented on the immaculate condition of the under-carraige and the 'as-new' condition of the stock parts....so i dunno what to think now....

either way i'm getting one of them 'Super-Strong' timing belts done soon just to be sure.....

A real sharp shifty used car salesman will know all about winding back or replacing the speedo, and all about wear on the steering wheel, carpet, drivers seat, drivers door, and pedal pads.

What the bugger will not change though, is the brake discs. They may even have been reground by the previous owner, but they will be always be thin on a very high mileage car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...