Jump to content
SAU Community

Recommended Posts

Hey all,

I just got my car back from tuning a few days ago.

Its a pretty much stock r33 gtr, just with a power fc and an exhaust.

Its running 222rwkw @ 12 psi.

im getting around 420km to a tank driving sensibly and around 360 to a tank when i give her a bit of a hard time.

is this a good healthy result? power wise and economy?

what do you experts think :(

cheers!

Link to comment
https://www.sau.com.au/forums/topic/270342-just-got-my-car-tuned-r33-gtr/
Share on other sites

  • Replies 75
  • Created
  • Last Reply

Top Posters In This Topic

Hey all,

I just got my car back from tuning a few days ago.

Its a pretty much stock r33 gtr, just with a power fc and an exhaust.

Its running 222rwkw @ 12 psi.

im getting around 420km to a tank driving sensibly and around 360 to a tank when i give her a bit of a hard time.

is this a good healthy result? power wise and economy?

what do you experts think :rolleyes:

cheers!

That sounds nice/healthy.

I get about the same as you, my mods are twin airpods, down, front pipes and high flow cat stock catback atm.

Stock +0.7 Bar (10.9 Psi) of boost.

If I really drive sensibly I can get 250kms just under half a tank, X 2 = 500kms, but I usually fill up when it hits half as half a tank last me about a week.

Plus you got an APexi Power FC which will help out with your air/fuel mixture.

hey, thanks for the info!

i've always wondered, are 32's lighter on fuel than 33's in general?

just curious!?

R32 GTR's are lighter, so there is less weight to push.

From memory I read this from some where...

R32 GTR = +0.7 (10.9 Psi) Bar Boost (Stock)

R33 GTR = +0.8 (12 Psi) Bar Boost (Stock)

R34 GTR = +0.9 (13 Psi) Bar Boost (Stock)

(I will have to check...)

So the more the R33 full boost, as apposed to the R32 full boost, the R33 will need more fuel as it is running a higher boost level.

But it's MARGINAL... So it should not make much of a difference but it will add up in the end.

hi all, thanks again for the comments and reassurance :devil:

here are some pics are requested -

apologies for the mess in the interior shot, i was sticking my turbo timer back on.

post-54322-1242660701_thumb.jpg post-54322-1242660756_thumb.jpg post-54322-1242660799_thumb.jpg

post-54322-1242660843_thumb.jpgpost-54322-1242660973_thumb.jpg

dude. that is dammmmm sexy. i love your instrument cluster ( nismo cluster ) i want that in white !!

awesome clean car.

Very tidy S3 mate, as for keeping it stock - yeah, right :(

With exhaust, front pipe, high flow panel filter in stock airbox and PowerFC my R33 just made 239RWKW, so power wise yours seems pretty much on the money.

No idea about fuel economy though, I just fill it up and go drive it some more >_<

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...