Jump to content
SAU Community

Gtr Drive Problems

skyline-lemans
 Share

Recommended Posts

skyline-lemans Apprentice

skyline-lemans

Posted
Posted

anyone know what could cause this??. The 4wd light comes on, then goes off as normal.

I was at a drag race and people told me that only the rears were spinning. This explains my awful launches and slow 1/4 mile times.. the track was untreated and I was using much too hard yokohama advan slicks. Got a 13.001 @186kmh and my girl is really capable of more than that...I was about the only person not using mk drag slicks...

Link to comment
https://www.sau.com.au/forums/topic/270426-gtr-drive-problems/
Share on other sites
skyline-lemans Apprentice

skyline-lemans

Posted
  • Author
Posted
Open your boot, take off the bit on the driver's side and check your ATTESSA fluid level

just checked it...the levels fine(a bit high), spun the wheels and the torque gauge shows power to the front.....my assistant said the fronts did nothing

blind_elk Grand Master

blind_elk

Posted
Posted

Just because wheels don't spin doesn't mean you have a problem. If anything, the fact that the rears break traction is the problem.

Go and read through any of the hundreds of threads that explain how the ATTESSA 4WD system works. Then decide if you actually have a problem.

skyline-lemans Apprentice

skyline-lemans

Posted
  • Author
Posted
Just because wheels don't spin doesn't mean you have a problem. If anything, the fact that the rears break traction is the problem.

Go and read through any of the hundreds of threads that explain how the ATTESSA 4WD system works. Then decide if you actually have a problem.

I know how it works...my other gtr works a treat...this one doesn't...

Beer Baron Grand Master

Beer Baron

Posted
Posted

it could be so many things. search for attesa diagnostics either google or in the forum and run the diagnostic sequence then check the diagnostic light flashes to see if any fault codes come up. if they do follow up whatever they indicate is not working. if nothing comes up check the basics first. do you have the same sized tyres all round? are all the wheel speed (ABS) sensors intact? they can be easily damaged as they are quite exposed. you've already checked the fluid level. can you hear the pump prime when the car is turned on? go to a workshop and get them to put a pressure gauge on the pump. good workshops will know how to test the awd and know what type of pressure the pump should be outputting under certain conditions.

anyway, start by checking for fault codes.

skyline-lemans Apprentice

skyline-lemans

Posted
  • Author
Posted
it could be so many things. search for attesa diagnostics either google or in the forum and run the diagnostic sequence then check the diagnostic light flashes to see if any fault codes come up. if they do follow up whatever they indicate is not working. if nothing comes up check the basics first. do you have the same sized tyres all round? are all the wheel speed (ABS) sensors intact? they can be easily damaged as they are quite exposed. you've already checked the fluid level. can you hear the pump prime when the car is turned on? go to a workshop and get them to put a pressure gauge on the pump. good workshops will know how to test the awd and know what type of pressure the pump should be outputting under certain conditions.

anyway, start by checking for fault codes.

no fault codes...no nasty noises...pump runs..4wd light goes out...fluid level good....

it has uprated lsd's, and whoever wired the rear fog light managed to somehow give the brake light permanent live...so the brake lights come on when the ignition is off and if you turn the ignition on to listen to the stereo...you get that bloody awful buzzer all the time...

maybe they have tapped into something they shouldn'e have !

skyline-lemans Apprentice

skyline-lemans

Posted
  • Author
Posted
no fault codes...no nasty noises...pump runs..4wd light goes out...fluid level good....

it has uprated lsd's, and whoever wired the rear fog light managed to somehow give the brake light permanent live...so the brake lights come on when the ignition is off and if you turn the ignition on to listen to the stereo...you get that bloody awful buzzer all the time...

maybe they have tapped into something they shouldn'e have !

emailed the people who tuned it and dyno'd it before I owned it..they only have a 2 wheel drive dyno and said they think they either remove the abs fuse...or disconnect one of the front wheel speed sensors....

now my car does have very very heavy steering, but I put this down to a dodgy speedo conversion when it was brought over from japan...

some_cs_student Veteran

some_cs_student

Posted
Posted
emailed the people who tuned it and dyno'd it before I owned it..they only have a 2 wheel drive dyno and said they think they either remove the abs fuse...or disconnect one of the front wheel speed sensors....

now my car does have very very heavy steering, but I put this down to a dodgy speedo conversion when it was brought over from japan...

Heavy steering? Dodgy speedo conversion?

Japan is in km/h, what has it been converted to?

Heavy steering may indicate the HICAS computer has been disconnected, but that is the 4 wheel steering system, not sure which models get the heavy steering, I know the R33 does...

skyline-lemans Apprentice

skyline-lemans

Posted
  • Author
Posted
Heavy steering? Dodgy speedo conversion?

Japan is in km/h, what has it been converted to?

Heavy steering may indicate the HICAS computer has been disconnected, but that is the 4 wheel steering system, not sure which models get the heavy steering, I know the R33 does...

unclipped the connector by the bonnet release.... turn on ignition and attessa pump runs constantly...reconnect.turn on ignition and nothing....should it prime when the ignition is switched on ????? is it usually so quiet you can't hear it..but can only feel the vibration?

skyline-lemans Apprentice

skyline-lemans

Posted
  • Author
Posted
Heavy steering? Dodgy speedo conversion?

Japan is in km/h, what has it been converted to?

Heavy steering may indicate the HICAS computer has been disconnected, but that is the 4 wheel steering system, not sure which models get the heavy steering, I know the R33 does...

it's been converted to mph....not sure how it was converted but the car has a full cage so think getting the clocks out might be a problem??

skyline-lemans Apprentice

skyline-lemans

Posted
  • Author
Posted

just lifted all 4 wheels, the fronts spin when in gear but you can stop them with your foot.

I disconnected the clip under the dash and this did not cause the pump to run constantly...... which relay is it that controls the attessa pump...the blue or the black???

Am i correct in thinking the pump should be on constantly when the clips disconnected..???

skyline-lemans Apprentice

skyline-lemans

Posted
  • Author
Posted

just bled the system, still no power to fronts....they can be stopped with your foot !!... tried to spinning the rears but the fronts still didn't perform... no error codes.....pump seems to work fine.....levels good......what it is?? pleasse somebody......

Jmaac Proficient

Jmaac

Posted
Posted

+1 rooted clutches in transfer case. They pulled the fuse before putting it on a 2wd dyno without bleeding pressure off to the transfer case (or mech. disconnecting it). Difference in steering may be because they didnt plug the speed sensor back in, Hicas uses it.

blind_elk Grand Master

blind_elk

Posted
Posted
just lifted all 4 wheels, the fronts spin when in gear but you can stop them with your foot.

If the fronts are spinning under these conditions, then my opinion is that the ATTESSA is working. What does the torque-split gauge say?

AFAIK, the front diff is open, so it would be possible to stop one side, and the other side would continue to be driven. Is that what happens?

If you remove the fuse (in a R33), the car goes to limp mode (I believe) - that makes it impossible to run it on a 2WD dyno.

heller44 Mentor

heller44

Posted
Posted

Just torque transfer by fluid coupling in the transfer case can produce the same effect.

I would suggest checking the pump again, and seeing if the pressure you are getting out is correct, not just hearing a noise.. R32 manual states between 294 and 490kPa (43-71psi).

If you are getting the correct pressure and still no drive, then clutch pack..

skyline-lemans Apprentice

skyline-lemans

Posted
  • Author
Posted
Just torque transfer by fluid coupling in the transfer case can produce the same effect.

I would suggest checking the pump again, and seeing if the pressure you are getting out is correct, not just hearing a noise.. R32 manual states between 294 and 490kPa (43-71psi).

If you are getting the correct pressure and still no drive, then clutch pack..

The bleed nipple under the pump....turned on the ignition.....about 10ml came out...then no more.... the pump did not run constantly..as I thought it was supposed to with the bleed connector disconnected..should this bleed fast, slow or should I not have done it?

When you turn the ignition on and off the actuator thing clunks and sometimes the pump comes on...not often though..

some_cs_student Veteran

some_cs_student

Posted
Posted

When I bled my system, you would turn on the ignition, and there would be a slight delay and the liquid starts coming out, it wasn't that slow but it took a while to get through the tank in the back of the boot.

I turned the ignition on and off at least 5 times to make sure I gave the pump a break, there's a tutorial on this somewhere.

The fact that its not pumping doesn't sound right...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...