Jump to content
SAU Community

Recommended Posts

I got the Toyota minolta 88C-V last night, and added a turbo, 1080hp i think, its fast and pretty good but my god its twitchy, Mind you im playing with a controller and traction control and ASM on so when its oversteering its catching the car and putting fairly bad understeer into it which shoots it straight off if your not careful. Has anyone found a way to fix this?

dont be useless. lose the extra turbo.. lose the TCS.. lose the ASM.. even with the controller its not hard to feather the throttle where you need to. dont forget those le mans cars are engineered to only turn properly at high speeds or under throttle, so if you slow down to much and have no throttle on going through a corner you will be absolutely murdering your potential lap time. even on extremely low speed corners you need to be at least partially on the gas through the corner to maintain proper grip and neutral steering

the same applies for virtually all le mans & F1 cars

But more power is always fun :P

Think it's just the asm catching the oversteer and making it unpredictable. Will have a go with it off next time. Need somewhere to clamp my wheel and pedals so I can race properly

Edited by 89CAL

Anyone else on here got an X1?

If so, what's your best Tsukuba lap? My best so far is 29.6

I got one last night that thing is stupid fast and hard to control with a pad, i did probly 10 laps with it and my best was a very very sloppy 32 something, I need lots of practice just to keep it on the track it is just so fast.

accelerating very slowly- the bumps knock it around quite badly, and it's very twitchy with the d.f set to minimum. also realized the toe-angles were set to - and +1 front and rear standard, which may have scrubbed some speed. car makes less power now so there's no point trying again

it's geared to do 507 (which you can't change), you should be able to get 490 or more if you cruise up behind a Le Mans car 3/4 of the way down the straight and get an aero tow

I think I only managed 420 or so in the veyron, but that was just a practice run to see if it would hit 400 with no other cars on the track. got my 111 feet per second or whatever it is lol so i was happy. Been hitting B-spec lately. My hot headed driver is getting quite good at level 12. Nowhere near as much frustration

farkk it.. old ps3 packed up good and proper last week. just went and bought a new slimline. how lucky was i to backup my gt5 data about 2mins before it broke.. although all my other game saves are down the tube.. ffs sony needs to sort their shit out and come up with a way to transfer saves off the old hdd

farkk it.. old ps3 packed up good and proper last week. just went and bought a new slimline. how lucky was i to backup my gt5 data about 2mins before it broke.. although all my other game saves are down the tube.. ffs sony needs to sort their shit out and come up with a way to transfer saves off the old hdd

erm, doesn't the "backup" utility do this?

I upgraded to a 500GB HDD and all my save games went across no worries. Just needed to re-sync the trophies.

erm, doesn't the "backup" utility do this?

I upgraded to a 500GB HDD and all my save games went across no worries. Just needed to re-sync the trophies.

i didnt upgrade, my console died. making it impossible to get access to my saves.

one time i tried the backup utility it tried to backup everything on the drive, movies, music, the lot. didnt have a flash drive big enough for it. i only need a backup of saves but it doesnt let you do that

i didnt upgrade, my console died. making it impossible to get access to my saves.

one time i tried the backup utility it tried to backup everything on the drive, movies, music, the lot. didnt have a flash drive big enough for it. i only need a backup of saves but it doesnt let you do that

I know, but you could still remove the HDD from the stuffed PS3, put it in the new PS3, perform the backup to an external HDD then put the original HDD back in the new PS3 and "restore"

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...