Jump to content
SAU Community

Recommended Posts

I've got a track day on Sat at Sandown and the forecast looks to be wet. I have RE01Rs for the road and RE55 (SR2s? - can't see the car now to confirm but not wet weather ones, just normal) for the track so not sure what's best for the day. I've run the RE55s and some Dunlop D01Js in the wet (road) and was always pleasantly suprised by the grip on offer.

Any thoughts on the best way to go? My guess would be that other than large amounts of standing water, the RE55s would be a better bet.

Commnets and suggestions please.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/276932-tyre-selection-for-a-wet-track/
Share on other sites

Thanks guys. I'll take a look at the forecast the day before and perhaps speak to someone who knows the track and see what their view is. Wish me luck as iIm nervous being on the track in the wet! I guess I'll have to slow down, feed the speed in, and not take any risks on the faster corners.

As it happens I did a track day in the wet last weekend. On RE55's. They were new though.

To be honest they are fine - even to the point where there are puddles on the track. Just try & drive around the said puddles as you can get aqua planing at spots you don't want to.

Corner grip is pretty low & your biggest issue will be having a lose under brakes. Just keep it straight & everything will be fine.

You can be confident that your times will be ok as most people who take road tyres wont be going hard & anyone on R compounds will be in the same boat as you.

I've done a hillclimb at Mt Cotton in heavy rain on RE55S. There were sheets of water running down the hills towards you. The RE55S were great in the wet there, but it is low speed compared to Sandown.

IMO semis are always faster in the wet than street tyres. I've certainly never been beaten by anyone running street rubber in the wet. And you don't see Improved Production guys swapping to road tyres in the rain - you can bet your arse if it was faster they would! Street tyres evacuate more water, but the hard compounds are not going to give you any grip on a cold wet surface.

slightly higher cold pressures in the wet - you won't generate as much heat in the tyre and won't get to your normal target hot inflation pressures. Try 2-4psi higher cold.

Thanks. Can you tell me off what base? e.g. normally set to 28psi cold for dry conditions. Run 28+4 for wet. etc etc.

the way I do it (it may not the best way but it works for me) is to aim for the same hot pressures as you normally end up with in the dry. On multi lap sprints that seems to generally be about 4psi higher than my normal cold starting pressure. So yes, if you normally start with 28psi cold, try 32 psi cold and see if you hit your normal hot pressure (probably around 36 I'm guessing?) after the first session, then adjust from there.

OK, lay it on me brothers. I need to be told directly what psi to set my tyres at tomorrow. __psi for a wet track. I'd just whack 30 in em without any further guidance so if that aint the figure, can you give me one? It'll be wet and cold at the track tomorrow so I'll not be stuffing around with pressures whilst I'm there - yes, I'm weak as piss. I'm also fiddling with the suspension so will only have time for that.

Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey keep the ideas coming, I'm always keen on projects! But, problem fixed!  I got a cheapie ozito scope from Bunnings and had a good look in and around the bearing and sensor hole. I couldn't see a smoking gun but the bearing looked a bit strange, especially when comparing with a new one. I thought the cover had come off the bearing magnets.  Sorry for pics of a screen, I didn't have an SD card.     Good thing I had the old one to inspect. So, given I'm like a pit crew with wheel bearings and luckily I had a spare bearing because I f**ked up my parts order, I decided to just smash it out. Got the old one out in about an hour. So much easier when the parts haven't had a chance to rust together yet. 😂 And, well, found the problem.    In the second pic at about the 8 o'clock position, you'll see what I think is the tip of the old sensor.  The new sensor has definitely been rubbing but it's all intact, just a little shiny so I'm hoping it's fine.  The car brakes perfectly now and no errors.  I think the job took about 2.5h in the end. 👍🏻 I really appreciate the help in here as usual. Thanks guys.
    • I was only looking because I saw some drops on the ground but it wasn't alot. Recently had it serviced will ask the mech to confirm. Find it strange that it looks standard though, can see in another photo of a random box 
    • So...not sure if you know if that has always been there or why you went looking. It could be old damage from a clutch explosion, or even just the gearbox got dropped somewhere along the line. Basically, you should seal it up to stop oil and dust getting into the bellhousing, but it doesn't matter too much and is not structural. I'd suggest something like a glob of JB Weld. BTW what gearbox oil are you running, I would guess the breather has been spewing it everywhere.
    • Hey Duncan thanks for your reply. Sorry mate I know the photos are shit.  Took another photo for reference. Seems the casing does have a hole in it looking on the net, fluid seeping out. Added a photo   
    • Very hard to make out what you mean, is it the squarish hole with redline shockproof (probably) under it? Is that pic from on top of the engine with the firewall to the left of pic and engine to the right? Either way, spray the area liberally with degreaser and try again, maybe circle the part you are worried about
×
×
  • Create New...