Jump to content
SAU Community

Recommended Posts

I've got a track day on Sat at Sandown and the forecast looks to be wet. I have RE01Rs for the road and RE55 (SR2s? - can't see the car now to confirm but not wet weather ones, just normal) for the track so not sure what's best for the day. I've run the RE55s and some Dunlop D01Js in the wet (road) and was always pleasantly suprised by the grip on offer.

Any thoughts on the best way to go? My guess would be that other than large amounts of standing water, the RE55s would be a better bet.

Commnets and suggestions please.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/276932-tyre-selection-for-a-wet-track/
Share on other sites

Thanks guys. I'll take a look at the forecast the day before and perhaps speak to someone who knows the track and see what their view is. Wish me luck as iIm nervous being on the track in the wet! I guess I'll have to slow down, feed the speed in, and not take any risks on the faster corners.

As it happens I did a track day in the wet last weekend. On RE55's. They were new though.

To be honest they are fine - even to the point where there are puddles on the track. Just try & drive around the said puddles as you can get aqua planing at spots you don't want to.

Corner grip is pretty low & your biggest issue will be having a lose under brakes. Just keep it straight & everything will be fine.

You can be confident that your times will be ok as most people who take road tyres wont be going hard & anyone on R compounds will be in the same boat as you.

I've done a hillclimb at Mt Cotton in heavy rain on RE55S. There were sheets of water running down the hills towards you. The RE55S were great in the wet there, but it is low speed compared to Sandown.

IMO semis are always faster in the wet than street tyres. I've certainly never been beaten by anyone running street rubber in the wet. And you don't see Improved Production guys swapping to road tyres in the rain - you can bet your arse if it was faster they would! Street tyres evacuate more water, but the hard compounds are not going to give you any grip on a cold wet surface.

slightly higher cold pressures in the wet - you won't generate as much heat in the tyre and won't get to your normal target hot inflation pressures. Try 2-4psi higher cold.

Thanks. Can you tell me off what base? e.g. normally set to 28psi cold for dry conditions. Run 28+4 for wet. etc etc.

the way I do it (it may not the best way but it works for me) is to aim for the same hot pressures as you normally end up with in the dry. On multi lap sprints that seems to generally be about 4psi higher than my normal cold starting pressure. So yes, if you normally start with 28psi cold, try 32 psi cold and see if you hit your normal hot pressure (probably around 36 I'm guessing?) after the first session, then adjust from there.

OK, lay it on me brothers. I need to be told directly what psi to set my tyres at tomorrow. __psi for a wet track. I'd just whack 30 in em without any further guidance so if that aint the figure, can you give me one? It'll be wet and cold at the track tomorrow so I'll not be stuffing around with pressures whilst I'm there - yes, I'm weak as piss. I'm also fiddling with the suspension so will only have time for that.

Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A realistic expectattion of how long it has to last also comes down to.... when do you think you will be banned from registering and driving old petrol powered shitters? It's 27 years since that thing was built. It probably rusted out 15 years ago. It was probably repaired and looked OK for another 10. If you do a similarish bodge job now, or perhaps slightly better with some actual rust conversion and glassing, then.... get another 10-15 years out of it, after which you'll only be permitted by the CCP to drive electric cars manufactured in their Shenzen zone anyway. 
    • Let me assume that the concern over a manual ECU is that the NeoDET that you have was an auto and has an auto ECU. That ECU will not be a problem, but you WILL have to Nistune it. And you would have to Nistune it even if you had a manual ECU, because the turbo ECUs will shit the bed if they do not have all the things that they were told they have to have, to be happy. The big one being the TCS CU, which you won't have in your car. Anyway, with an auto ECU (which I have running my originally auto NeoDET in an R32) Nistune allows you to put in a Stagea image which doesn't panic about the absent TCS, and allows you to override a whle bunch of other annoyances that would otherwise see the check engine light on 100% of the time. Also, you can't wind up the power very far on the stock NeoDET ECUs without Nistune, because the boost sensor gets in the way. Nistune allows you to push that problem much further up the dial. Do you even have the boost sensor with the engine? Without it, you are SOL and will need an aftermarket ECU (or to find a sensor somewhere, god knows where). I can't tell you what the wiring loom differences are in a 34. But what Duncan said above needs to be considered. When you say "loom", does that include the transmission loom? Because you will need to swap out the auto tranny loom for the equivalent manual loom, and get rid of the neutral/park start interlock (basically hot wire it).
    • I have had the r3c in for years now, maybe close to 7 years and it has never missed a beat, anyone can drive it. Super easy to drive around town, the hotter it gets does get a little hard but it holds the power easy as 
    • Shit thing to find eh? I guess the big issue is that whatever "fix" you do now, it might slow the rust down but won't fix it. I just wanted to add that in no way is fixing sheet metal in 3 dimensions the place to start with welding....that is a pro only job because its too hard to work out where things should be, let alone doing a clean enough job that it can look OK and still be strong too.  I needed to get a new rear quarter panel on the GTR and it took a pro weeks to get the old one off cleanly, new one on in the right place and looking somewhat like it should have with most of the previous connecting panels in place. Gluing a couple of bits of metal together with a welder in the garage is doable, but that is totally different to doing panel  replacement
    • This seems to be a very popular swap since all the turbo skyline prices went through the roof! I'll let someone more familiar chime in, but I understand that yes you probably want to swap the loom in to swap out the auto TCM stuff. You should not assume everything just plugs in either, you need to check at least the ECU wiring diagram for any differences at the plug at the left headlight and probably the ones near the ECU that join the dash loom too  
×
×
  • Create New...