Jump to content
SAU Community

Recommended Posts

I've got a track day on Sat at Sandown and the forecast looks to be wet. I have RE01Rs for the road and RE55 (SR2s? - can't see the car now to confirm but not wet weather ones, just normal) for the track so not sure what's best for the day. I've run the RE55s and some Dunlop D01Js in the wet (road) and was always pleasantly suprised by the grip on offer.

Any thoughts on the best way to go? My guess would be that other than large amounts of standing water, the RE55s would be a better bet.

Commnets and suggestions please.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/276932-tyre-selection-for-a-wet-track/
Share on other sites

Thanks guys. I'll take a look at the forecast the day before and perhaps speak to someone who knows the track and see what their view is. Wish me luck as iIm nervous being on the track in the wet! I guess I'll have to slow down, feed the speed in, and not take any risks on the faster corners.

As it happens I did a track day in the wet last weekend. On RE55's. They were new though.

To be honest they are fine - even to the point where there are puddles on the track. Just try & drive around the said puddles as you can get aqua planing at spots you don't want to.

Corner grip is pretty low & your biggest issue will be having a lose under brakes. Just keep it straight & everything will be fine.

You can be confident that your times will be ok as most people who take road tyres wont be going hard & anyone on R compounds will be in the same boat as you.

I've done a hillclimb at Mt Cotton in heavy rain on RE55S. There were sheets of water running down the hills towards you. The RE55S were great in the wet there, but it is low speed compared to Sandown.

IMO semis are always faster in the wet than street tyres. I've certainly never been beaten by anyone running street rubber in the wet. And you don't see Improved Production guys swapping to road tyres in the rain - you can bet your arse if it was faster they would! Street tyres evacuate more water, but the hard compounds are not going to give you any grip on a cold wet surface.

slightly higher cold pressures in the wet - you won't generate as much heat in the tyre and won't get to your normal target hot inflation pressures. Try 2-4psi higher cold.

Thanks. Can you tell me off what base? e.g. normally set to 28psi cold for dry conditions. Run 28+4 for wet. etc etc.

the way I do it (it may not the best way but it works for me) is to aim for the same hot pressures as you normally end up with in the dry. On multi lap sprints that seems to generally be about 4psi higher than my normal cold starting pressure. So yes, if you normally start with 28psi cold, try 32 psi cold and see if you hit your normal hot pressure (probably around 36 I'm guessing?) after the first session, then adjust from there.

OK, lay it on me brothers. I need to be told directly what psi to set my tyres at tomorrow. __psi for a wet track. I'd just whack 30 in em without any further guidance so if that aint the figure, can you give me one? It'll be wet and cold at the track tomorrow so I'll not be stuffing around with pressures whilst I'm there - yes, I'm weak as piss. I'm also fiddling with the suspension so will only have time for that.

Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...