Jump to content
SAU Community

Recommended Posts

I've got a track day on Sat at Sandown and the forecast looks to be wet. I have RE01Rs for the road and RE55 (SR2s? - can't see the car now to confirm but not wet weather ones, just normal) for the track so not sure what's best for the day. I've run the RE55s and some Dunlop D01Js in the wet (road) and was always pleasantly suprised by the grip on offer.

Any thoughts on the best way to go? My guess would be that other than large amounts of standing water, the RE55s would be a better bet.

Commnets and suggestions please.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/276932-tyre-selection-for-a-wet-track/
Share on other sites

Thanks guys. I'll take a look at the forecast the day before and perhaps speak to someone who knows the track and see what their view is. Wish me luck as iIm nervous being on the track in the wet! I guess I'll have to slow down, feed the speed in, and not take any risks on the faster corners.

As it happens I did a track day in the wet last weekend. On RE55's. They were new though.

To be honest they are fine - even to the point where there are puddles on the track. Just try & drive around the said puddles as you can get aqua planing at spots you don't want to.

Corner grip is pretty low & your biggest issue will be having a lose under brakes. Just keep it straight & everything will be fine.

You can be confident that your times will be ok as most people who take road tyres wont be going hard & anyone on R compounds will be in the same boat as you.

I've done a hillclimb at Mt Cotton in heavy rain on RE55S. There were sheets of water running down the hills towards you. The RE55S were great in the wet there, but it is low speed compared to Sandown.

IMO semis are always faster in the wet than street tyres. I've certainly never been beaten by anyone running street rubber in the wet. And you don't see Improved Production guys swapping to road tyres in the rain - you can bet your arse if it was faster they would! Street tyres evacuate more water, but the hard compounds are not going to give you any grip on a cold wet surface.

slightly higher cold pressures in the wet - you won't generate as much heat in the tyre and won't get to your normal target hot inflation pressures. Try 2-4psi higher cold.

Thanks. Can you tell me off what base? e.g. normally set to 28psi cold for dry conditions. Run 28+4 for wet. etc etc.

the way I do it (it may not the best way but it works for me) is to aim for the same hot pressures as you normally end up with in the dry. On multi lap sprints that seems to generally be about 4psi higher than my normal cold starting pressure. So yes, if you normally start with 28psi cold, try 32 psi cold and see if you hit your normal hot pressure (probably around 36 I'm guessing?) after the first session, then adjust from there.

OK, lay it on me brothers. I need to be told directly what psi to set my tyres at tomorrow. __psi for a wet track. I'd just whack 30 in em without any further guidance so if that aint the figure, can you give me one? It'll be wet and cold at the track tomorrow so I'll not be stuffing around with pressures whilst I'm there - yes, I'm weak as piss. I'm also fiddling with the suspension so will only have time for that.

Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
×
×
  • Create New...