Jump to content
SAU Community

Recommended Posts

Ok so a mate suggested to me the other day that since I am running standard injectors and fuel reg, that until I can afford to get a remap/Nistune RB20 tune done, that I should take out my Microtech LT10S (the usual overfueling, shit fuel economy, horrible cold starts, fouling plugs, the fact that WOT = smokescreen deployed, and a EPA warning letter on top of that!) and replace with a standard RB25 ECU (think its all wired up still into the R32 loom).

Now assuming that wiring is all okay, am I likely to run into any major issues from running FMIC, KKR 480 turbo (boost set to actuator pressure of 8 psi) and turbo back exhaust? The motor is a Series 1 Stagea motor, would I be any better off with the Stagea ECU or just a normal R33 Series 1 do?

I do have an airflow meter sitting in the intake pipe albeit disconnected, and the O2 & VCT are disconnected.

Link to comment
https://www.sau.com.au/forums/topic/280128-microtech-removal-questions/
Share on other sites

hard to say, but personally I would think the only way you'll know for sure is try it. half of us will say it wont work, and the other half will say it will at the end of the day there is a sure fire way of knowing.....

I do have an airflow meter sitting in the intake pipe albeit disconnected, and the O2 & VCT are disconnected.

So do you intend on connecting them? AFM you won't get away with, the other 2 yes, but it's going to run like shit without VCT and o2.

If you can sort out the wiring, then provided you stick to 8psi then I can't see a reason why it wouldn't work.

nah I will connect everything up, there are around 69000 R33's around here so I'm sure I'd be able to get a lend of one, its more fingers crossed that the loom hasn't been butchered, but I'm assuming that there's no major differences in fuel maps etc for Stagea vs R33?

Hopefully the ATTESSA *might* run with a stock ECU as well, but I'm not holding my breath.

Yeah it's mainly come about because I'm so sick and tired of the way the Microtech behaves, but then when you're travelling 400+km to get a decent tuner it's not a cheap exercise at all.

  • 1 month later...

spose ill do a bit of an update; finally got a stock computer, threw it in, hooked up AFM... and nothing! I'd forgotten that the Microtech had a relay set up in the boot for the fuel pump so stock computer wouldn't prime! I'll be getting a mate to rewire it for me in the near future, then we'll see what happens...

Ok so a mate suggested to me the other day that since I am running standard injectors and fuel reg, that until I can afford to get a remap/Nistune RB20 tune done, that I should take out my Microtech LT10S (the usual overfueling, shit fuel economy, horrible cold starts, fouling plugs, the fact that WOT = smokescreen deployed, and a EPA warning letter on top of that!) and replace with a standard RB25 ECU (think its all wired up still into the R32 loom).

Now assuming that wiring is all okay, am I likely to run into any major issues from running FMIC, KKR 480 turbo (boost set to actuator pressure of 8 psi) and turbo back exhaust? The motor is a Series 1 Stagea motor, would I be any better off with the Stagea ECU or just a normal R33 Series 1 do?

I do have an airflow meter sitting in the intake pipe albeit disconnected, and the O2 & VCT are disconnected.

the stagea ecu is remappable with a type 4 nistune board andif tuned right passes all the epa tests.

nah gonna sell it to some sucker with a dirty 30 or a rotary owner :)

URAS: I thought that the type 4 board was only compatable with the NEO ECU? That's how I read the Nistune website anyway. Mine is a Series 1 Stagea motor with the old school RB25 and ignitor module.

nah gonna sell it to some sucker with a dirty 30 or a rotary owner :)

URAS: I thought that the type 4 board was only compatable with the NEO ECU? That's how I read the Nistune website anyway. Mine is a Series 1 Stagea motor with the old school RB25 and ignitor module.

ah yep ser1 needs the z32 ecu trick, sorry should have read your post better sorry.

will likely not bother with Z32 and just go RB20 remap and ditch the VCT since I already have a stock RB20 ECU lying around.

best running a jaycar switch then, ive got some dyno tests i did here with and without the vct and the hole in the mid range is about 15-19rwkw deep....

  • 6 months later...

might bump this up again since I'm once again looking at this, I have no idea if the standard plug is for the R32 or R33 ECU, will this matter? when I plugged in the R33 ECU the fuel pump refused to prime, however there is a relay type thing for it in the wiring in the boot, would i need to circumvent that?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...