Jump to content
SAU Community

Recommended Posts

Haha yeah i'm serious i got the receipt for it, bloody ridiculous. Cheers for the link NXTIME ill check it out tomorrow, also Marko R1 where did you purchase yours from.

www.purplepig.com.au

industrial suppliers

Man, this is what i want my dream skyline to be like; hand built, fast as... well anything, and an r32 :D

I'm looking forward to seeing this finished man, the closest thing i'm doing to working on a car is finding average audio parts for the incoming pulsar :)

Hope everything goes well bro. It had better do under 10's :( haha

Hi Guys

Finally Figured out how to put pictures up properly so here's a heap more:

PS If it doesn't do a 10 sec pass straight up, ill burn it to the ground hahaha!!!!

FRONT BUMPER GONNA LOOK SOMETHING LIKE THIS:

7222_1223180866769_1446408764_30620607_208298_n.jpg

TBO CARBON FIBRE DOORS 5.9KG EACH

16235_1286732735526_1446408764_30793143_393683_n.jpg

CARBON FIBRE BOOT

16235_1286733375542_1446408764_30793158_3495540_n.jpg

CARBON DOORS FITTED TO CAR

16235_1286733535546_1446408764_30793161_2668588_n.jpg

BRIDE ZETA III LOW MAX WITH 6 POINT TAKATA HARNESS FOR DRIVER AND 4 POINT FOR PASSENGER

16235_1295288589417_1446408764_30811070_6346227_n.jpg

CARBON FIBRE DASH IN CONSTRUCTION

19645_1303514555061_1446408764_30830361_1487680_n.jpg

SUPERIOR AUTO CREATIVE CARBON INTERIOR GOODIES

14104_1366555731051_1446408764_30978845_7591610_n.jpg

CENTER CONSOLE PAINTED 2 PAC BLACK WITH CARBON TRIMS

14104_1366555811053_1446408764_30978847_3226497_n.jpg

WORKS BELL STEERING WHEEL AND QUICK RELEASE SETUP

14104_1366555891055_1446408764_30978849_4315258_n.jpg

ROLL CAGE PAINTED

27180_1384894189501_1446408764_31015180_5472069_n.jpg

PWR CROSS FLOW RADIATOR 55MM CORE

32101_1469769751337_1446408764_31202024_2195362_n.jpg

PWR PLUS THERMO

32101_1469769831339_1446408764_31202025_7060684_n.jpg

MASSIVE FUEL SYSTEM

32101_1469770191348_1446408764_31202033_3748792_n.jpg

Got the carbon goodies from RHD Japan, yeah the boot could be getting a custom drag wing mounted to it, as we are gonna run the factory panels for street trim (cause of the cops and want sleeper look) and use all the carbon goodies for serious race events.

Hi Guys

Finally Figured out how to put pictures up properly so here's a heap more:

PS If it doesn't do a 10 sec pass straight up, ill burn it to the ground hahaha!!!!

FRONT BUMPER GONNA LOOK SOMETHING LIKE THIS:

7222_1223180866769_1446408764_30620607_208298_n.jpg

TBO CARBON FIBRE DOORS 5.9KG EACH

16235_1286732735526_1446408764_30793143_393683_n.jpg

CARBON FIBRE BOOT

16235_1286733375542_1446408764_30793158_3495540_n.jpg

CARBON DOORS FITTED TO CAR

16235_1286733535546_1446408764_30793161_2668588_n.jpg

BRIDE ZETA III LOW MAX WITH 6 POINT TAKATA HARNESS FOR DRIVER AND 4 POINT FOR PASSENGER

16235_1295288589417_1446408764_30811070_6346227_n.jpg

CARBON FIBRE DASH IN CONSTRUCTION

19645_1303514555061_1446408764_30830361_1487680_n.jpg

SUPERIOR AUTO CREATIVE CARBON INTERIOR GOODIES

14104_1366555731051_1446408764_30978845_7591610_n.jpg

CENTER CONSOLE PAINTED 2 PAC BLACK WITH CARBON TRIMS

14104_1366555811053_1446408764_30978847_3226497_n.jpg

WORKS BELL STEERING WHEEL AND QUICK RELEASE SETUP

14104_1366555891055_1446408764_30978849_4315258_n.jpg

ROLL CAGE PAINTED

27180_1384894189501_1446408764_31015180_5472069_n.jpg

PWR CROSS FLOW RADIATOR 55MM CORE

32101_1469769751337_1446408764_31202024_2195362_n.jpg

PWR PLUS THERMO

32101_1469769831339_1446408764_31202025_7060684_n.jpg

MASSIVE FUEL SYSTEM

32101_1469770191348_1446408764_31202033_3748792_n.jpg

Very Nice indeed!!!

Hi Guys Just an Update..

Waiting on turbo to get Adel wiggins Ferral welded on, also had to send the Throttle body back to Hypertune as they will dissasemble it and weld the 4" Wiggins Ferral on for us and reassemble etc. I finished wiring the 5 fuel pumps up today on seperate relays all controlled by there own pilot switchs in the cab.

Hoping to Order the rest of the -4 braid soon to finish off boost lines and other little fiddly jobs.. my dad will be speaking with Mark Jacobson this monday in brissy, hopefully to arange a rough date for when the car will be heading down that way to get run in and tuned.

If anyones looking at ordering Adel Wiggins clamps I have researched everyone under the sun.. ended up dealing with Gas Motorsports, the clamps are rediculously expensive but boy do look shit hot. haha

Hey mate nice build so far. But it looks to me as though you have a lot of the rear of your radiator core blocked off with the aliminium plate might pay to make some new brackets as there isnt much point having such a big core if the airflow cant get thru there because such a large area is blocked off. And just wondering why 5 fuel pumps ?.

Hi Guys Just an Update..

Waiting on turbo to get Adel wiggins Ferral welded on, also had to send the Throttle body back to Hypertune as they will dissasemble it and weld the 4" Wiggins Ferral on for us and reassemble etc. I finished wiring the 5 fuel pumps up today on seperate relays all controlled by there own pilot switchs in the cab.

Hoping to Order the rest of the -4 braid soon to finish off boost lines and other little fiddly jobs.. my dad will be speaking with Mark Jacobson this monday in brissy, hopefully to arange a rough date for when the car will be heading down that way to get run in and tuned.

If anyones looking at ordering Adel Wiggins clamps I have researched everyone under the sun.. ended up dealing with Gas Motorsports, the clamps are rediculously expensive but boy do look shit hot. haha

Did you guys solid mount the engine to the chassis? The wiggins clamps don't have any flex, so if your motor moves and the pipe work is secured down to the chassis/body- somthing is going to give and it aint gonna be the wiggins clamps.

GL

Justin.

Did you guys solid mount the engine to the chassis? The wiggins clamps don't have any flex, so if your motor moves and the pipe work is secured down to the chassis/body- somthing is going to give and it aint gonna be the wiggins clamps.

GL

Justin.

Edited by AD4M

Hi Guys just some reply's to ur questions..

first one to you dazmo, yes the back of the radiator is completely covered, this is the new design from PWR used on the Aston Martins Cars.. has a thermo fan and 3 rubber flaps which we havent put in yet.. when the car is iddling the flaps close and draw more air through the radiator.. but when driving along the flaps open up the air is alowed to pass through.

Five fuel pumps, haha yes one is for a lift pump to the SARD 5L surge tank, and four pumps for when the car runs on methanol. Our alternator has been rewound to 120Amps from the standard 90Amps because each pump draws 13Amps and CDI will pack a punch too.

second to Xrated, we have welded our engine mounts solid as a rock.. we didnt use wiggins clamps on the intercooler and stayed with normal silicon hose for flex there if needed.

  • 2 weeks later...

Hi Guys

Here's an update for you's:

Progress so far, most of the wiring is done, the engine has been put in for the very last time and everything bolted in now and is there for good. The 1.25 inch Adel Wiggins Clamps have turned up for the radiator, so that will be getting fabricated soon. The New brake rotors have also turned up so that will be getting put together as well.

As the pictures will show the interior trim is getting put in (What is left of it) so its starting to look like something!!!!

Cheers

Benny

38512_1527263988657_1446408764_31349766_1098724_n.jpg

38512_1527264028658_1446408764_31349767_173474_n.jpg

38512_1527264068659_1446408764_31349768_7758820_n.jpg

38512_1527264108660_1446408764_31349769_515383_n.jpg

38512_1527264148661_1446408764_31349770_6669037_n.jpg

37846_1527269188787_1446408764_31349774_4685051_n.jpg

37846_1527269228788_1446408764_31349775_5074607_n.jpg

37846_1527269268789_1446408764_31349776_7550496_n.jpg

37846_1527269308790_1446408764_31349777_3747385_n.jpg

37846_1527269348791_1446408764_31349778_5418027_n.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
    • Unsolicited advice? Keep the engine as close to stock as you can. Nothing wrong with adding some boost and making a little more power, but given where you are, you really don't want to try to make it into a monster. I can't imagine the roads are up to it, and the lack of locla support when it grenades will be a ball ache. FWIW, If there is a dyno around that you can access, then brand new injectors are a good idea, which will lead you to (at least) putting a Nistune in it, which will allow you to put an R35 AFM on it, all of which will make it possible to make it much much nicer to drive and live with.
×
×
  • Create New...