Jump to content
SAU Community

Fast & Furious Skyline Stolen From Hollywood Garage


Recommended Posts

Found this funny, though I'd share

Fast & Furious Skyline stolen from Hollywood garage May 17th 2009 at 1:44PM

paul_walker_nissan_gt-r.jpg

It took two years to build it in reality, ten seconds of montage to put it together on screen, and about ten minutes to steal it. In a rare automotive example of life imitating art imitating life, the Nissan Skyline that Paul Walker drove in the latest Fast & Furious movie was stolen from its storage facility in Los Angeles.

Although dressed up to look like a full-on R34 GT-R for the movie, the car underneath was actually a lower-spec GT-S. Reports indicate that thieves, evidently knowing the car was inside, broke through a metal door and ripped off that specific car, leaving the rest but sideswiping a Studebaker and a Porsche Boxster on the way out. And to make matters worse, the car, valued at around $75,000, wasn't even insured. Considering the movie grossed $72.5 million in opening-weekend box office sales alone, we doubt the seventy-five grand will be terribly missed.

Original http://www.autoblog.com/2009/05/17/i-fast-...llywood-garage/

GT-S ??? is that what we call the GT-T but n/a equiv ER34

i the movie its clear and obvious BNR34 dash cluster with 4wd and a-lsd lights in fail mode

so its an ER34 rear wheel drive with BNR34 kit for action shots etc, but interior is BNR34 with left hand drive and hacked 4wd and a-lsd

i just cant understant how it was woth $75,000? and i remember seeing the movie on the big screen and hated every second of it just wanted to slap the director in the face with my .....

and how dumb would you feel stealing a fake gtr haha

Yea the obvious reason why they are so cheap and popular here is because japan and australia drive on the same side when I lived in NY an R33 GTST would prob cost about $25g's US unconverted

75k USD for a R34 GT-T modded to look like an R34 GTR. Why don't you just friggin buy an R34 GTR? Seriously... I can't imagine a secondhand R34 GTR costing more than a Viper (approx 75k), including say 10-20k for a LHD conversion.

if doggy look alike r34 gtr's are worth $75k us dolla might start exporting them by the boat load lol

just watch the movie you can tell there not to bright lol maybe thats why paul and vin didnt make it to aus because they realized where not that stupid over here down under.

Damn it would make it easier if all cars were RHD and all units in metric. UK, Japan, Australia, India, SE Asia all drive on the correct side. Doesn't it make sense to do the most skill-requiring procedure (steering) with your dominant hand and the less skill-requiring ones (shifting, turning up the music, eating, touching girls) with the non-dominant hand?

It's the USA's fault. If they go RHD, the rest of the undeveloped world will follow. Then, hey, great savings for auto makers and consumers everywhere in the world. :)

world's most expensive GT (seeing as there's no such thing as an R34 GTS).

Lol, yeah, just realised in the pic as well that it's an unconverted RHD R34 GT. Sh!t that skyline exporting business is looking mighty attractive right now Travis :)

Damn it would make it easier if all cars were RHD and all units in metric. UK, Japan, Australia, India, SE Asia all drive on the correct side. Doesn't it make sense to do the most skill-requiring procedure (steering) with your dominant hand and the less skill-requiring ones (shifting, turning up the music, eating, touching girls) with the non-dominant hand?

It's the USA's fault. If they go RHD, the rest of the undeveloped world will follow. Then, hey, great savings for auto makers and consumers everywhere in the world. :angry:

Someone has their priorities in order.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...