Jump to content
SAU Community

Highflow

scotty nm35
 Share

Recommended Posts

scotty nm35 Grand Master

scotty nm35

Posted
  • Author
Posted

I asked them the same thing, he said... Its the same as the nissan patrol box. You can go manual but would have to ditch the attesa. All wheel drive or Rear only. Of course then you would have to run a 350z ecu or full computer and loose all other sensors and cpus like abs? not to mention grabbing the clutch pedal bits from???

This gearbox should be able to handle heaps of power now and snap into gear, just like a manual. Im going for a higher stall too due to the slightly higher lag, If its anything like my mates XR6 box they just did, I will be very happy.

Link to comment
https://www.sau.com.au/forums/topic/282170-highflow/page/2/#findComment-4753209
Share on other sites
nickcorr Proficient

nickcorr

Posted
Posted

Patrol transfer case does not have a "on demand" setting nor a centre diff, so cannot be used on tarmac in 4WD.

I think that is what they were getting at.

Patrol is part time 4WD, Stagea is AWD.. gotta love a bit of marketing...

Whilst we are on how strong transmissions are, there is an off the shelf kit to fit Patrol gearbox and transfer case into a Landcruiser.. Apparently the LC transfer case is made of glass...

Link to comment
https://www.sau.com.au/forums/topic/282170-highflow/page/2/#findComment-4753840
Share on other sites
prince_skyline Community Regular

prince_skyline

Posted
Posted

Spoke to Kyp at ATP today. My turbo is finished (as you would know Scotty) and was being delivered to R E tonight for refit. Kyp told me what you are doing Scotty - sounds great! Will post some pics up of the original damage to mine over w/e. Looking forward to getting the car back...early to mid next week i hope. :P

Now for the exhaust......off to that thread!!

Link to comment
https://www.sau.com.au/forums/topic/282170-highflow/page/2/#findComment-4753858
Share on other sites
Jetwreck Grand Master

Jetwreck

Posted
Posted
do want a manual!

surely the 34 getrag would be able to squeeze in there somewhere

I went down this road a while back.....while the Patrol box was stong the 34 Getrag is probably the best option because it can handle the HP and Torque once you start tweeking.....it was also built as a sports box and we all know it will handle the MN35 AWD system. The only real problem I stumbled over was the bell housing.....everything else was pretty straight forward. The let down was cost.....if I could find a good one with the transfer case for $1,500 I would have gone for it.

Link to comment
https://www.sau.com.au/forums/topic/282170-highflow/page/2/#findComment-4754156
Share on other sites
Daleo Grand Master

Daleo

Posted
Posted
Secret mens buisness apparently, no cameras allowed. :) I did ask for you.

I was going to get some pics of the car too, but theres not much of it left.

Heres a pic of the coilovers tho.

I would love to hear how you get on with these, they seem quite the bargain, if they're not too harsh.

Link to comment
https://www.sau.com.au/forums/topic/282170-highflow/page/2/#findComment-4754542
Share on other sites
scotty nm35 Grand Master

scotty nm35

Posted
  • Author
Posted
I would love to hear how you get on with these, they seem quite the bargain, if they're not too harsh.

The BC coilovers ceartainly look the part, I will fit them next week hopefully. Lots to do, I have to rebuild turbo, refit turbo, install trans cooler, ive got some heat shielding sheets to install on the inner guard and firewall around the turbo. Then fit the coilovers and get a wheel alignment. All this while the gearbox is getting rebuilt.

I need to fit an engine oil cooler also if I can find a cheapie. Speaking of which.. has anybody fitted one before?

I noticed the hose coming out of the filter block, can this be tapped into for the oil cooler? I hope so, it looks simple.

post-63525-1249620947_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/282170-highflow/page/2/#findComment-4754971
Share on other sites
scotty nm35 Grand Master

scotty nm35

Posted
  • Author
Posted
Scotty, that hose is from the radiator. The circular bit that your filter screws into is the OE oil cooler and, obviously, has coolant pumped through it.

Ok thanks mate. So I will still need a full oil cooler kit.

Link to comment
https://www.sau.com.au/forums/topic/282170-highflow/page/2/#findComment-4754997
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...