Jump to content
SAU Community

Recommended Posts

i searched this but didnt get any results, so sorry if its already been covered

i want to remove those ugly rotor gaurds and was wondering if anyone has done this b4 and knows whats involved, i cant find any bolts on the backside of the gaurds and am thinking they might be spot welded on on the rotor side of the gaurd???

thanks for any help you can give!

Link to comment
https://www.sau.com.au/forums/topic/285617-r34-disc-rotor-gaurd-removal/
Share on other sites

Remove the caliper and then remove the rotor. You will then have full access to the stone guard... you cant slide it off hence you need to hack it off.

Use either tip snips, an angle grinder or a combination of the two :D

Remove the caliper and then remove the rotor. You will then have full access to the stone guard... you cant slide it off hence you need to hack it off.

Use either tip snips, an angle grinder or a combination of the two :D

cool, should make a prety tidy job of it, thanks guys

Dont do the irreversible.

Think long and hard when it comes to modifications that are hard to undo.

There is no need to cut anything. Ive only removed the fronts before. Not sure about the rears. But this involved removing the wheel, caliper, rotor, dust cap for the hub, split pin, hud nut, then hub. The hub nut on my car was 30mm and should not be on so tight that you break 2 breaker bars getting it off. After you remove this the rotor dust shield slides off. Sometimes with a little force needed.

Be careful when taking the hub off not to lose anything (ie. bearings and washer) and make sure you put everything back on in the right order. A new split pin must be installed to prevent the hub nut coming off.

I take no responsibility for any damage or misfortune that happens to you/anyone or your/anyones car during or after the process.

If your still unsure about the whole process get a qualified mechanic to do it for you.

I don't think hub needs to come off - although if you want them out in one piece, calipers and rotors should come out (or temporarily have them out of the way), which is no big deal.

I think they are interference fit to hub as there is nothing else holding them in place.

It's always nice to have things out in one piece and in serviceable condition, in this case a pair of tin snips would be the best way to go.

ceffy is talking about a31/s13 style fronts where you can easily remove the spindle to get the backing plate off in one piece.

Unfortunately the front end of a skyline is completely different and short of having your front stub axle and bearings pressed out and back in you are stuck with cutting it off.

  • 3 weeks later...
Dont do the irreversible.

Think long and hard when it comes to modifications that are hard to undo.

There is no need to cut anything. Ive only removed the fronts before. Not sure about the rears. But this involved removing the wheel, caliper, rotor, dust cap for the hub, split pin, hud nut, then hub. The hub nut on my car was 30mm and should not be on so tight that you break 2 breaker bars getting it off. After you remove this the rotor dust shield slides off. Sometimes with a little force needed.

Be careful when taking the hub off not to lose anything (ie. bearings and washer) and make sure you put everything back on in the right order. A new split pin must be installed to prevent the hub nut coming off.

I take no responsibility for any damage or misfortune that happens to you/anyone or your/anyones car during or after the process.

If your still unsure about the whole process get a qualified mechanic to do it for you.

Exactly what he says, I did this on my silvia and going to do it on my GT-T when I get my R34 Brembos.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are black hose clamps as well if you care. Plazmaman for example sells some: https://plazmaman.com/product/black-hose-clamps-premium-quality-stainless-breeze/
    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
×
×
  • Create New...