Jump to content
SAU Community

Recommended Posts

Thank you for your comments everyone! Its been great sharing my build with you!

Big Engine Update as we approach the finale of this build! I hope you like what you see - keep the comments coming

Built engine finds its rightful home in the engine bay! Engine bay has been repainted gloss white. The original factory matt off white colour looks too dull.

Main colour scheme is 'black and white Storm-Trooper' look.

dscf00112.jpg

dscf00172c.jpg

dscf0024v.jpg

Engine cam covers and oil catch can painted in crinkled black finish; all hoses and attachments are black as well. A few words that come to mind to describe the engine bay: 'mean'; 'industrial'; 'military' and 'stealth'.

Close up of crinkled paint finish. The paint is not uniformed in appearance and gives it a very unique look. It is different to the textured finish on say the Mines' signature purple or the Nismo S1; R1 red cam engine covers.

Note 'HKS Power' logo on the V cam cover - looks tough!

dscf0039qv.jpg

dscf0040ls.jpg

dscf0032k.jpg

Detailed images of V Cam badge; V Cam solenoid, wiring and oil line input and HKS limited edition oil cap

dscf0037r.jpg

dscf0035ct.jpg

dscf0038tf.jpg

Other supporting accessories:

Racepace custom Oil catch can and washer fluid combination, again in crinkled black finish. Hoses are neatly tucked away to be unobtrusive:

dscf0016dl.jpg

dscf0021se.jpg

dscf0022bv.jpg

dscf0041h.jpg

Racepace spec custom PWR based 50mm radiator:

dscf0017l.jpg

dscf0044m.jpg

Nismo Z Tune 100mm thick intercooler:

dscf0018xc.jpg

dscf0015dp.jpg

SARD 700cc injectors denoted by the light blue colour on the injector body:

dscf0029m.jpg

dscf0036jz.jpg

Nismo Air intake duct:

dscf0019rj.jpg

Nismo aluminum piping:

dscf0023av.jpg

dscf0033k.jpg

dscf0043ws.jpg

I still have a few more surprises up my sleeve. (Hint - I am a wheel whore and the black and white Storm trooper theme...... :thumbsup: )

Thank you guys for feedback!

Gts30t Posted Yesterday, 08:13 AM

Looks awesome matt, a nice strut bar would really finish off that bay

I planned to replace stock strut bar with Cusco Carbon fibre ALC40 when funds permit. Also planned Garage Defend Carbon radiator cooling panel.

Aaron34 Posted Yesterday, 08:28 PM

beautiful job. No other way to describe it. Wow..

Now it needs to be shipped to Germany with mine and Snowmans to be truely enjoyed...

Pity I don't have the driving skills like you guys to make the most of it! :(

BBGTR Posted Yesterday, 08:35 PM

I always like to see someone who is more anal than me when it comes to preparation.

Yes, I am super 'anal'. Believe it or not, I polish the rear bar after a every drive, because so much soot and fumes get blown out the rear end. As the car is white, if the fumes are left longer than a few days, the rear bumper; boot; spoiler supports and rear light cover goes yellow.

bigmikespec Posted Today, 02:13 PM

Was there a decision made to keep the orginal plenum instead of going for a Nismo version?

I sold the Nismo plenum to another fellow member. Beno said that the Nismo plenum is good for mildly tuned RBs; but for RB28 its actually going to reduce output! He measured the inlet and the Nismo one is smaller in diameter compared to the stock item. The chamber of the Nismo carries more volume though and therefore beneficial for standard capacity RBs.

awesome car mate and great choice of bits. there is not anything I can really fault with it. it will be an absolute weapon to drive and should give years of fun. :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...