Jump to content
SAU Community

Recommended Posts

Hey guys.

Trying to get a few guys together to go for a cool calm and collected drive on Sunday. A mate and I were thinking about leaving from Engadine Maccas at noon and heading down to Port Kembla lookout or Robinson for a bite to eat. Just thought i'd put the feelers out to see if anyone is interested in tagging along. So far there is only myself (R33 GTR) and my mate who has a R32 GTR the the possibility of two others.

Link to comment
https://www.sau.com.au/forums/topic/288537-sunday-20th-sep-09-drive/
Share on other sites

G'day guys I'm the guy in the R32 GTR that'll be coming along as well. We were checking the weather and so far...so good :cool: so I'll give the old girl a wash and head on down!

Should be a great drive, and the weather looks to be on our side for once!

C'mon who's in!

Hehe,

OzFoz Foresters will be meeting at 9 at Heathcote Maccas > Albion Pk > Mac Pass > Kangaroo Valley Rd > Berry >

More traffic down there later on when you're going tho'

Terry, I'm assuming thats 9 AM Sunday monring? Would be a great drive. Are you going?

Looks like I have clutch issues. Well not the clutch itself. I had a leak, replaced the lines and now i cant get the take up point on the clutch I had before. I have a mate who is a mechanic coming around tomorrow to see if he can work out what the hell is going on..... It may have to be postponed to the week after :)

hey Fairy Penguin lol

I might be down, I think some of the boys/girls might be chilling at my place coz Phong's out of action since he fell off the Gixxer.

btw, check this out:

if I come tmr, I'll make sure to block off the bov haha

G'day guys I'm the guy in the R32 GTR that'll be coming along as well. We were checking the weather and so far...so good :O so I'll give the old girl a wash and head on down!

Should be a great drive, and the weather looks to be on our side for once!

C'mon who's in!

Matt?

Terry, I'm assuming thats 9 AM Sunday monring? Would be a great drive. Are you going?

I was going to be there at 9am today with a new 22mm whiteline rear sway bar installed BUT > BUT I got rear-ended last Sunday.

Fortunately, it was the Forrie & NOT the 'Line. Still, I've only had the XT for 1 month and then this happens...

  • 2 weeks later...


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...