Jump to content
SAU Community

Recommended Posts

I have searched these forums for info on how to make an R33 GTR into RWD, and found little helpful advise based on R33's. I'd like for someone who has done this before, by removing fuse or front shaft (from transfer case to front diff) to comment on how this was done / any problems encountered?

Also Mine is a V-Spec, so dunno if this makes things more difficult.

I understand pulling the fuse isn't the answer (on R33), but what does this do exactly?

Link to comment
https://www.sau.com.au/forums/topic/29019-how-to-r33-gtr-rwd/
Share on other sites

All you need to do is pull the fuse in the boot and bleed the 4wd pump of fluid, no need to drop front drive shafts.. I've had mine done to dyno it and causes no probs at all. Just make sure they do the screw up properly when they've finished otherwise you leak fluid... You lose around 60ml of transmission fluid that's all...

Mines a Vspec too...

Cheers

Brett

I may be wrong here, but I'm sure HKS or one of the name brand makes a "rod thingy". check out www.greenline.jp I think I saw one there.

I also remember checking out a GTR Vspec that had heeps of these gadgets/switches, one to switch the HICAS on/off, RWD/4WD on/off, Rod to reduce the sound of the exhaust, an on/off for the ATTESSA...etc

He's a SAU member, can't find the link but user name was En_One his contact numbers are 0415210220 or 0421531468 or email to [email protected]

Maybe give him a try, seemed to have every gadget under the Al Quaida Sun.

meshmesh are you referring to the HKS Drag Controller?

Buggered if I know??? All I can remember is that the car had 3 flick switches where the ashtray goes, & a rod about the size of a pushbike tyre pump, that was on the passenger side of the centre console. Also, I about 100% sure, he said one of them makes the car RWD only, which he used for track work. Is that a drag controller?

On a non-V-spec you just pull two fuses, one in the boot and one in the cabin and bingo, RWD central. I only drove for a short time and the clutch was slipping anyway so can't really say what it is like to drive as a RWD.

But that really doesn't help the original poster. But might save someone with a non-V-spec doing something silly like pulling their car to bits...

My understanding is that the remove the fuse option is not safe with R33s and later, apparently there is some wear on the clutch packs that does not occur with R32s.

And without meaning to hijack, when the forums were lost a thread re the HKS torque split controller was lost. Does anyone have any experience with it?

Thanks for the opinions guys.

CerealKiller / Blitz - I want RWD for drift and skidpan days. 4WD sticks too well and therefore limits my fun. harhar (evil laugh)

EVL R33 (Brett) - Have you removed this fluid yourself before? Could you perhaps elaborate on how this is done? Where is the 4WD pump found?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just bought a 2002 Stagea 250tRS VR-X Four AERO VQ25DET and spent the last two weekends cleaning and detailing it.. still have to do the wheels and the engine bay but the rest of it came up nice. Imported 2011 to S.A. and I'm the third owner since it was imported. I met the guy who brought it over, he went to Japan and picked out the car, bought it and ordered the wheels. He also gave me a list of stuff he did to the car with receipts. Coil overs (I have the original springs), 3" exhaust from the dump pipe back no cat, Custom dump pipe,(I have the original exhaust), Plenum spacer, 18" custom Work XSA wheels (need restoring, I've made a start..), Shift kit put through the 5 speed tiptronic auto, TV and menus/screens changed to english, Australian DTV tuner installed in rear. I've just had four new discs and new pads as well as all the fluids including the brake fluid replaced. I have all the receipts for the last 15 years and the import papers in a nice folder. Car looks great, goes like hell but fuel economy is not a thing lol.. pics next..
    • I ended up in this rut again lol, and used a shit ton of filler. One thing I can't understand is, even after using a big long block and going in long X pattern strokes, I always end up at bare metal again with no filler, and my repair started at one end of the door and now I've chased my tail to almost the other end of the door. I was thinking of hitting the panel with a hammer where it might be a high spot and making everything low then filling it, I did this on a small section on my other door by mistake and I think I fixed it lol. Is this a bad idea? The other thing is with guidecoat, whether it's the powder or spray, after I sand all the guide coat off, it doesn't reveal anything for me in terms of high spots and low spots and makes it especially hard when it's bare metal (at least in powdered form), am I doing something wrong here, or likely a high spot I keep going over and creating valleys? Lastly, stupid question but, is it possible that after sanding if I only sand over the filler area where I know to be a dent that it's impossible for me to dig into that dent? Unless there are other problems which I missed.  
    • Yeah the rule of thumb with an LS is 7psi per 1000rpm. That is decidedly not enough at 6800rpm. I mainly looked for the scenarios where knock started to be picked up and it was later in the session when things were hotter, and oil was thinner, and the pressure was lower than it should be. (i.e very horrible). I am hoping with thicker oil (I was running Penrite ten tenths 10-40, the manual specifies 10-30) that does not leak that it's much improved at that time!!! I am using Project Mu Club Racer CR pads. I'm also using the Project Mu 335C fluid. The symptoms imply that it was fluid that boiled, but no bubbles seemed pretty weird to me when I bled it today. I want to try Castrol SRF as it has a much higher wet temp but, well, I have new Project Mu fluid lol... so I should at least use that. The pedal on track was really noticable. It went from basically normal feeling to instantly near-floor. The car did pull up as before, it was just very much nearly at the floor before the brakes engaged. At that point I pretty much decided the day was very done, it did *kinda* come back during that very slow cooldown lap into the pits. Felt perfectly fine driving home.
    • f**king around with the bro
×
×
  • Create New...