Jump to content
SAU Community

Recommended Posts

Followed A?L-01L (Grey GTS-4) down Norton Street :wavey:  

Oh and I think you need a tune:  when you put your foot on it a huge cloud of black smoke emerged :D

Lucien.

I'm having trouble getting into your link below it wan't accept my my log in???

Can anyone help from Admin of SAU??? Please!

Followed A?L-01L (Grey GTS-4) down Norton Street :wavey:  

Oh and I think you need a tune:  when you put your foot on it a huge cloud of black smoke emerged :)

Lucien.

:wavey: back at ya.

Do you live round the inner west too?

I know i need a tune its running rich as :Oops:

By the way its a 4 door GTSt , not gts4.

thanks

Adam.

:wavey: back at ya.

Do you live round the inner west too?

I know i need a tune its running rich as :Oops:  

By the way its a 4 door GTSt , not gts4.

thanks

Adam.

I live in Leichhardt. Apologies for the failure to correctly identify you: I must have been exhausted from my efforts at gym :)

Lucien

Drunkan,

Yeah, it went ok. #1 turbo is leaking a bit of oil and a bit of water, so we need to re-work #1, the CAMs whistle a little so Im not sure about that. The HKS dumps dont have a spot for the exhaust temp, so its dead and I have an issue with boost and the oil temp. But other then that its fine!

Drunkan,

   Yeah, it went ok. #1 turbo is leaking a bit of oil and a bit of water, so we need to re-work #1, the CAMs whistle a little so Im not sure about that. The HKS dumps dont have a spot for the exhaust temp, so its dead and I have an issue with boost and the oil temp. But other then that its fine!

:ohnoes:

Did you buy the correct HKS extension kit Paul? Sounds like you might have dump pipes meant for a 32 or 33.

spotted GUN-32R Marron R32 at Carrigton Rd, castle hill at the tyre place. had huge, 18 inch volks and 275/35/18's on all 4.

cool that was me, are you ati-something, white r32 gtr with a black rear spoiler?

i saw that at the corner of carrington and victoria today thought maybe you?

I live in Leichhardt.  Apologies for the failure to correctly identify you:  I must have been exhausted from my efforts at gym :D

Lucien

You live in Leichhardt?!?

So do i !!!

I dont think i have ever seen you around before though.

Thanks

Adam

spotted nismo34? tom?

black r34 GTT

apparently lives a few roads down from me but ive never seen him before hahaha

anyways, nice car... black is hot!!

rather poor performance from me too but oh wellz ^^, will get it sorted after exams

cheers

Eric

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...