Jump to content
SAU Community

Recommended Posts

Followed A?L-01L (Grey GTS-4) down Norton Street :wavey:  

Oh and I think you need a tune:  when you put your foot on it a huge cloud of black smoke emerged :D

Lucien.

I'm having trouble getting into your link below it wan't accept my my log in???

Can anyone help from Admin of SAU??? Please!

Followed A?L-01L (Grey GTS-4) down Norton Street :wavey:  

Oh and I think you need a tune:  when you put your foot on it a huge cloud of black smoke emerged :)

Lucien.

:wavey: back at ya.

Do you live round the inner west too?

I know i need a tune its running rich as :Oops:

By the way its a 4 door GTSt , not gts4.

thanks

Adam.

:wavey: back at ya.

Do you live round the inner west too?

I know i need a tune its running rich as :Oops:  

By the way its a 4 door GTSt , not gts4.

thanks

Adam.

I live in Leichhardt. Apologies for the failure to correctly identify you: I must have been exhausted from my efforts at gym :)

Lucien

Drunkan,

Yeah, it went ok. #1 turbo is leaking a bit of oil and a bit of water, so we need to re-work #1, the CAMs whistle a little so Im not sure about that. The HKS dumps dont have a spot for the exhaust temp, so its dead and I have an issue with boost and the oil temp. But other then that its fine!

Drunkan,

   Yeah, it went ok. #1 turbo is leaking a bit of oil and a bit of water, so we need to re-work #1, the CAMs whistle a little so Im not sure about that. The HKS dumps dont have a spot for the exhaust temp, so its dead and I have an issue with boost and the oil temp. But other then that its fine!

:ohnoes:

Did you buy the correct HKS extension kit Paul? Sounds like you might have dump pipes meant for a 32 or 33.

spotted GUN-32R Marron R32 at Carrigton Rd, castle hill at the tyre place. had huge, 18 inch volks and 275/35/18's on all 4.

cool that was me, are you ati-something, white r32 gtr with a black rear spoiler?

i saw that at the corner of carrington and victoria today thought maybe you?

I live in Leichhardt.  Apologies for the failure to correctly identify you:  I must have been exhausted from my efforts at gym :D

Lucien

You live in Leichhardt?!?

So do i !!!

I dont think i have ever seen you around before though.

Thanks

Adam

spotted nismo34? tom?

black r34 GTT

apparently lives a few roads down from me but ive never seen him before hahaha

anyways, nice car... black is hot!!

rather poor performance from me too but oh wellz ^^, will get it sorted after exams

cheers

Eric

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...