Jump to content
SAU Community

Recommended Posts

heheh thats k I was turn and wave but was too scared that the guy in front of me might suddenly stop!

LOL it gets like that on the Anzac Bridge! I have a theory that *most* of the world's crap drivers run over it each day!

I spotted a white R32 with a black or carbon bonnet this afternoon @ around 3pm (wasn't paying attention to the time) on Seven Hills Road heading away from Baulko, it was near the school and where that field/skate park is. Didn't catch the plates, but I did give a quick flash of the high-beams.

I was in the Stagea and heading towards Baulko to get some last-minute pressies (came away emty-handed, oh well...)

I spotted a white R32 with a black or carbon bonnet this afternoon @ around 3pm (wasn't paying attention to the time) on Seven Hills Road heading away from Baulko, it was near the school and where that field/skate park is.  Didn't catch the plates, but I did give a quick flash of the high-beams.

I was in the Stagea and heading towards Baulko to get some last-minute pressies (came away emty-handed, oh well...)

cool i got spootted yeah!!

what car were u in..

i remeber being highbeamed by a non skyline..

i thought it was a cop warning..

pfft zeds........350z...yeah I rate them......

but 300zx...meh.....I dont wanna be flamed by some of the zed lovers....so ill keep my comments to myself.

hahaha! good call... these peeps don't mess around :lol: :lol: :lol:

veery passionate!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...