Jump to content
SAU Community

Recommended Posts

Saw r33 gtr with the plates "ONISMO" on ryde road the other afternoon. Looked hot as hell. Dunno whether he saw me though :thanks:

Spotted that car before parked near Olympic Park on a SAU cruise

All the staff in my office are also female (no joke) so that is also another reason why alcohol is not a good idea :P

If you can offer me a job that is easier, same rate of pay, and definitely not on-call 24/7 - I'll happily bust my balls for ya!

spoted so many skylines tonight around the dural castle hill area.. but only noticed it was a 'line when i looked in my mirror and saw the lights.. gf is getting pritty good at it now too. can pick out a 32 33 and 34 at night just from the lights hehe. still gota teach her the difference betweena gtst and gtr

Spotted quite a few Skylines (mostly R33s, but there was one nice dark silver R34 four-door too) out at Penriff(!) tonight.

Went to the Car Audio & Excellence sale there, but couldn't find anything worth buying. Need speakers, but I refuse to buy them without listening, and the Soundstream ones I did listen to and liked were $769 ON SALE, reduced from $999. Way overboard!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...