Jump to content
SAU Community

Recommended Posts

Sam, it was parked in Franklin Street. Although I didn't get too good a look at it, I'm sure it had chromies (nothing too over the top, thank god) and a rear wing on it - I'm pretty sure I would have recognised your car even if it was from just a quick glance.

ah cool.. yeh def wasnt me then lol

spotted some dark colour 34 4door i think parked around the corner from me in the dark near the park.(Get a Room) LoL

and a silver r34 BBZ *** come hooning past me on Doonside Road

not even 5minutes ago.

spotted a few imports in the carpark on my first day at work today :)

also spotted caine at MAC center at lunch today... didnt get the chance to scream out or stop u.. i was going up the elevator wen u got to the bottom lol...

mainly s15's no lines tho :D

Edited by mass_iv
spotted a few imports in the carpark on my first day at work today :)

also spotted caine at MAC center at lunch today... didnt get the chance to scream out or stop u.. i was going up the elevator wen u got to the bottom lol...

mainly s15's no lines tho :)

*clears throat*

Spotted Marsss on Parra rd near Petersham heading towards the city.

I was in the Hiace going the opposite direction, hahaa beeped at your for aaages..

yeah got the SMS.. as you can understand.. if a Hiace is beeping at me.. i ignore it with gusto... but i'll know next time :rofl:

y is it everytime i spot somone they're never a member of SAU?!? I've been meaning to actually send in my membership form/money but i've been out of work (its been really hard because my skyline needs some work done and i can't afford it) I think i've figured out y i haven't been spotted...because it looks like a piece of junk with bad paint...i just wish i had a decent looking 'line!

I think i spotted security today at lunchtime outside subway/oportos off canterbury/milperra rd

If not, it was a yellow 33, bodykit - plates started with auf i think

I was the guy driving the gunmetal 33 >_<

y is it everytime i spot somone they're never a member of SAU?!? I've been meaning to actually send in my membership form/money but i've been out of work (its been really hard because my skyline needs some work done and i can't afford it) I think i've figured out y i haven't been spotted...because it looks like a piece of junk with bad paint...i just wish i had a decent looking 'line!

you'll find that alot of the cars here are a work in progress mate. mine being one of them. took me a while to get the paint sorted.

I think i spotted security today at lunchtime outside subway/oportos off canterbury/milperra rd

If not, it was a yellow 33, bodykit - plates started with auf i think

I was the guy driving the gunmetal 33 :)

yeah mate that was me, i saw you but didnt get a wave or anything so i didnt think too much of it. and when you see a bright yellow r33 you KNOW its me, not think :domokun: . my mate [username: vexed on here] was there too with the blue r33.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...