Jump to content
SAU Community

Recommended Posts

ATD-50T yellow r34gtt with white wheels on douglas rd just then on my way home, dude you left your lights on!

oh yeh spotted that race looking 32gtr Gibson or something plus a silver 32gtr next to it at some pub on camden valley rd near denham court.

Spotted a wine red s1 R33 with unpainted s2 rear wing on Old Windsor Road around Stanhope Gardens this arvo, driver was on his P's.

Also spotted and cruised with a silver s2 R33 from Toongabbie and on into Parra this arvo around 5.30pm. I gave him a thumbs up and got one back. I think the rego was BCO30W or similar.

Saw a black R32 gts-t with vic numberplate "TXB-***" this morning going towards the city on gore hill freeway...gave him a wave....but only got a confused/angry look :banana:...

oh and saw a guy taking pictures of his white series 2 R33 in Ultimo :)

Edited by ChrisCross

Spotted a shmick lookin r32 in BP servo at Mortdale. Plates i think were mr 32.

Today had a clean looking s2 r33 behind me on Boundary Rd and quickly taking over me on Forest Rd. The little laser just couldn't handle the pressure! ;)

Plates were AMY then i think 033? But was half asleep so probably wrong.

spotted an engine and gearbox-less R33 being towed by a hektik R31!

Oh, t'was Anna's! hai!

rub it in why dont ya ;)

Spotted evil bish making off like a thief in the nite with my rear strut brace............

Spotted a couple of R33s just now(midnightish), too dark to get details but you were driving along the Pac Hwy between Berowra and Mt Colah, about 2 mins apart from each other ;)

Edited by Zilch*
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...