Jump to content
SAU Community

Recommended Posts

2 silver R35s in the space of an hour!

one at the original harry cafe de wheels down in woollomoo and another heading to edgecliff at about 1426 today, plate '206' anyone know what that could mean? the plate not the co incidence.

oh and a burgundy R32 gtst parked just after brookvale oval with plates MIX 32T, very clean.

(last night a light coloured R34 gtst AWK 973 driving very slowly along parra road towards the city through annandale.

2 silver R35s in the space of an hour!

one at the original harry cafe de wheels down in woollomoo and another heading to edgecliff at about 1426 today, plate '206' anyone know what that could mean? the plate not the co incidence.

R35s still have a lot of presence don't they.

206 Numeral-only plate - my guess is it doesn't mean anything; the numeral-only plates are quite valuable, the fewer the digits the better. Often used as a status symbol and/or investment but values seem to be very speculative.

dropped the gf back to dee why and spotted these on the journey..

the pictured r34 was in the back streets of dee why about 1130 am and gave it a bit of a squirt when he saw me in the rear view mirror, had a hard time keeping up until he parted ways with me at a roundabout, think i saw an SAU sticker so thanks for the run if your on here.

also an r33 that looks identical to mine ARR 42V at 1210 near warringah mall and finally a white very clean R33 GTR parked only military road mosman facing away from the bridge exit, god they look soo much nicer than gt-st's...sniff.

post-60574-0-74732700-1297568185_thumb.jpg

Edited by hamiltonau

Spotted a dark purple R33 GTSt this afternoon rolling through Toongabbie. Spotted it turning onto the railway overpass bridge, then turning right onto Fitzwilliam Road at the roundabout.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...