Jump to content
SAU Community

Recommended Posts

Spotted a gunmetal grey (?) R32 on a tow truck in belco last night.. didnt look like there was damage but then again i saw it for a split second.. any1z from here?

Advance spotted :) - me on friday going to check out my boss' new buy... RH9 with a completely rebuilt engine from Jun in japan! so excited :laugh:

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/283/#findComment-2001946
Share on other sites

spotted what looked to be Nik's car outside of integra this morning

Go past today and it looks completely different again :D (if I could post picture I would, but it has no front end on it at the moment).

me on friday going to check out my boss' new buy... RH9 with a completely rebuilt engine from Jun in japan! so excited

Should be an absolute weapon when its back on the road running around.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/283/#findComment-2002645
Share on other sites

get used to it. it'll be his car soon......

spotted a silver R33 going south along adelaide ave this arvo about 2ish. it was wingless with a sweet bodykit. got a wave, gave one back. your car looked awesome man, you on here?

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/283/#findComment-2006471
Share on other sites

7:55pm: Silver R33 GT-R coming off the Parkway turning into Weston Creek

7:57pm: Yellow R34 25GT-t "NISSAN" on Hindmarsh Drive towards Woden

7:59pm: Silver R33 GT-R as above coming back out of Weston Creek :D

Disclaimer - times posted above are not exact, however are accurate to within about 1 minute :)

ALWAYS see a Skyline on Hindmarsh Drive when I'm out walking in the evening.....

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/283/#findComment-2006779
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...