Jump to content
SAU Community

Recommended Posts

I was there tonight, black 33, might have been me if it was around 9.30-10ish?

Thats the one..! You may have seen me.. I was in the car with chicks spreading themselves all over the car, people wanting to know me, taking pictures, sponsors wanting to pay me $$$ to put their sticker on my car. "I aint commercial BIATCHES!"

No.. I was in my dads camry... :P

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/377/#findComment-2869114
Share on other sites

Spotted a silver series 2 R33 driving down belconnen way last night around 5pm, TALKING ON HIS PHONE. I wish people would stop talking on their phones while driving, especially Skylines, it gives us a bad name.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/377/#findComment-2870140
Share on other sites

Think i saw mivec. maroon 33 with the same kit. Going along parkway around 1ish yesterday. Very nice car. I was in the white 33 sedan.

What time? I was only out and about at roughly 930 or 130ish

I did see a white 33 but I don't think it was yesterday, maybe the day before when I went out to take piccies of teh car.

Edited by MIVEC
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/377/#findComment-2870808
Share on other sites

Thats the one..! You may have seen me.. I was in the car with chicks spreading themselves all over the car, people wanting to know me, taking pictures, sponsors wanting to pay me $$$ to put their sticker on my car. "I aint commercial BIATCHES!"

No.. I was in my dads camry... :P

:)

i need to get me a camry!!!

;)

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/377/#findComment-2872759
Share on other sites

Tool in Sydney rocked pretty f**kin hard aswell :laugh:

tool2.jpg

HAR! I am master pit photographer!

saw tool at bdo in melbourne and also their sideshow in sydney at which i went backstage to hang out with adam afterwards ha!!!

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/377/#findComment-2873971
Share on other sites

saw tool at bdo in melbourne

My mate saw them at BDO melbourne and at the Sidney Myer Music Bowl. Apparently BDO blew goats, you could hardly hear maynard at all. Not to mention it was a Festival, and that is of course a dirty dirty place of worship.

December, maybe November

*dances*

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/377/#findComment-2874174
Share on other sites

That was me! Damn those wheels on your car look wide. I like :)

thx

I like the wheels, I am getting sick of the colour though, Don't know which colour to choose atm, wish they hadn't been powdercoated gold :)

Edited by CeJay
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/377/#findComment-2874697
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...