Jump to content
SAU Community

Recommended Posts

Spotted a nice looking R32 GTR "GTRCHIK" tonight down the parkway.

Do we have a chick with a modded GTR in Canberra?

That would have been me :D

Yes you do have a chick with a modded GTR in Canberra hehe. It is a V-Spec II and has the Trust bodykit. I imported it in October 2006, have been working on it in WA but only got it brought to Canberra when I moved back from Perth (alas the WA number plates).

Edited by GTRChik
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/485/#findComment-3916309
Share on other sites

well I drove around heaps today and all I saw was a black series1 R33 turning out of Fyshwick onto Dairy Flat, paint looked very clean and shiny, had aftermarket rims.

And a silver R33 GTR on Pirie Street Fyshwick.

both about 1.30pm

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/485/#findComment-3925032
Share on other sites

Maroon 33 S1 this morning in Fyshwick with blue plates resembling SKI...

Black 32 in Civic heading towards Canberra Avenue - I was the guy in the Nissan jacket.

Me accidentally p1ssing off a gold Forester this morning... oops :P Hope it wasn't Leech, I'm sure I'll find out soon if it was.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/485/#findComment-3931218
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...