Jump to content
SAU Community

Recommended Posts

Maroon r32 GTR at the set of lights next to bunnings in fyshwick today. Cant remember the plates but were something like ***-GTR

Also, i keep seeing the white r33 GTS out the front of signworld in mitchell, has a SAU sticker on it so im guessing its someone on here?

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/656/#findComment-5654213
Share on other sites

i was driving the work van, big fat hyundai iload.

With working paying for fuel its quite alot cheaper than driving my whale around

And Sorry Melly, but i only caught a glimpse of the bonnet in the rear view as he turned off, i'll try and be more accurate next time :D

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/656/#findComment-5655040
Share on other sites

Black R33 GTST on Federal highway this morning followed by a cement truck turning the corner from Barton Highway which then tipped over. Crazy shit!

hopefully the cement truck driver is ok..........that being said that would have be hilarious to see

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/656/#findComment-5655118
Share on other sites

I don't think watching other people have accidents is hilarious. Had he been on the inside lane and there been a car on the other side things could have been much uglier. The lights went green and about 5 cars had already stopped. It looked like he'd already kicked the windscreen out and people were helping him out at the time so from what I could see he looked ok.

Stupid mistake but I imagine he's going to get in plenty of poo from his employer and a nice neg driving or equivalent for his troubles.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/656/#findComment-5655252
Share on other sites

I'm sad that I never get spotted on my 3 minute drive to work each day! :(

Know the feeling. I drive around on the weekends and to and from civic each Tues and Thurs Evening, never get spotted either.. Been taking the old car the 10mins to work, so it is parked and exposed to attention.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/656/#findComment-5655338
Share on other sites

I forgot from Friday.... spotted cruising the main drag of the Hyper D (yes srsly), 2 Ferrari's, one white convertible and one deep red/cherry one. f**k they looked good. I'm not sure what model.

Also spotted a guy in a Corolla today wearing driving gloves :huh: Like, he had a tshirt, cap, sunnies.... and black leather gloves WTF

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/656/#findComment-5660960
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...