Jump to content
SAU Community

Recommended Posts

butt failed

Shaun not Shuan - Doh !

+ you forgot Shorn and Shawn

Huge butt fail - like ghetto butt fail :(

Shawn was the first one - you butt failed ! Never seen Shorn :O I guess I forgot Shawjn (silent J) :D

Edited by RosieR34
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/909/#findComment-7148471
Share on other sites

Spotted Silver 33 GTS-t with a minor overheating issue on Athlon last night around 9pm

Stopped to lend a hand but left just offering advice :thumbsup:

Flush properly

Make certain thermostat is in correct way (replaced that day)

Use Coolant

Do with heater on full

- is water pump pumping ?

Bleed air off before driving, if possible

Check water level after driving for a while

Oh - it was a relatively new Rad as well.

Edited by Sinista32
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/909/#findComment-7149234
Share on other sites

Black R35 GTR in the city about 2pm parked outside bags to go on Bunda street (ACT plates)

AND

Silver lamboghini gallardo, also on Bunda street about 1:30pm - had the top down and looked like you could fry an egg on the drivers bald head!

the only way you can afford a lambo at a young age is if you win the lotto....

its always the old bald guys driving expensive cars...

when im retired ill be owning some insane supercar just for fun, then ill get a heap of plastic surgery so I don't look stupid driving it......

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/909/#findComment-7149421
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...