Jump to content
SAU Community

Recommended Posts

EDIT: oops, fixed title...

hey guys,

Some of this has come up before a few times already but I just thought I'd give my thoughts on it.

I decided to remove the panel off the front of the M35 airbox to see what the difference would be. I'm too stingy to buy a powerduct (like on the V35 and PM35 stagea) so I just left it as is, my rationale being that the airbox is right up against the front anyway, and when you're in motion it'll be getting nice fresh air.

Anyway, so obviously the first thing I noticed was the sound. It is awesome. I just didn't expect it to be anything like what it is. Makes the car sound soooooo much better under boost/heavy throttle. My fuel usage did suffer over the following 300km though because I just had to hear it over and over again...which meant a heavier-than-normal right foot...but this should sort itself out as I get more used to it. :down:

The other thing I did last week was grab a bottle of Caltex Techron 5000 and pour it in the fuel tank. Its available from most caltex servo's for about $13.

With both of these things its hard to say conclusively whether there is a benefit or whether I've just had a good run, but the car seems to breathe better (ie. less restriction when you press the accelerator) and overall has better performance all-round. In any case the engine sound is definitely conclusive - and its worth doing just for that!

I highly recommend the techron, but obviously do your own research if you're not sure about it...

Thing is, I always use bp ultimate but still, I know my intake is covered in black soot so I figured the engine internals could be as well...

The cleaning agent in any 98RON fuel is probably pretty good but none of them are anywhere near as concentrated as a bottle of techron 5000. I've read many good reviews about it online which is why I thought of giving it a go. it gets 2 thumbs up from me :)

Edited by pixel8r
Link to comment
https://www.sau.com.au/forums/topic/300887-airbox-panel-on-m35/
Share on other sites

I just fitted an intake on an M35 yesterday, I used some 1 inch square foam to seal around the front of the airbox and trimmed 4 inches off the bonnet rubber, worked great. No need for a powa duct.

I just fitted an intake on an M35 yesterday, I used some 1 inch square foam to seal around the front of the airbox and trimmed 4 inches off the bonnet rubber, worked great. No need for a powa duct.

got a pic?

Nub question, but how do you remove the front section of the air box to replace the filter?

I've taken off the front 'lip' duct, unbolted the airbox itself (10mm bolt on the right), detached what I presume is the airflow meter and unclamped the rubber hose from the back of the box.

But the air box is still attached to something underneath it and there isn't enough room to get front of the air box off enough to swap the filters.

Suggestions?

Lovely job thanks Scotty.... :cheers:

post-20696-1261441284_thumb.jpg He even trimmed the rubber edge on the bonnet... post-20696-1261441298_thumb.jpg

Nicely showing off the new intake piping there too :santa:

Sound = 10/10

Performance = a bit subjective. Definitely dont think I've lost any performance. It does certainly feel like there is less restriction - particularly at low revs. More kw? I dont know. Even if there was, it would be very slight. I just love the sound :)

Yes the pick up is much better than previously, so fuel consumption not an issue, just enjoying it...

But going down to the Valley at the weekend so will see how it does then..

So have you noticed a difference Nick?

Or are you still learning how to drive it economically?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...