Jump to content
SAU Community

Recommended Posts

EDIT: oops, fixed title...

hey guys,

Some of this has come up before a few times already but I just thought I'd give my thoughts on it.

I decided to remove the panel off the front of the M35 airbox to see what the difference would be. I'm too stingy to buy a powerduct (like on the V35 and PM35 stagea) so I just left it as is, my rationale being that the airbox is right up against the front anyway, and when you're in motion it'll be getting nice fresh air.

Anyway, so obviously the first thing I noticed was the sound. It is awesome. I just didn't expect it to be anything like what it is. Makes the car sound soooooo much better under boost/heavy throttle. My fuel usage did suffer over the following 300km though because I just had to hear it over and over again...which meant a heavier-than-normal right foot...but this should sort itself out as I get more used to it. :down:

The other thing I did last week was grab a bottle of Caltex Techron 5000 and pour it in the fuel tank. Its available from most caltex servo's for about $13.

With both of these things its hard to say conclusively whether there is a benefit or whether I've just had a good run, but the car seems to breathe better (ie. less restriction when you press the accelerator) and overall has better performance all-round. In any case the engine sound is definitely conclusive - and its worth doing just for that!

I highly recommend the techron, but obviously do your own research if you're not sure about it...

Thing is, I always use bp ultimate but still, I know my intake is covered in black soot so I figured the engine internals could be as well...

The cleaning agent in any 98RON fuel is probably pretty good but none of them are anywhere near as concentrated as a bottle of techron 5000. I've read many good reviews about it online which is why I thought of giving it a go. it gets 2 thumbs up from me :)

Edited by pixel8r
Link to comment
https://www.sau.com.au/forums/topic/300887-airbox-panel-on-m35/
Share on other sites

I just fitted an intake on an M35 yesterday, I used some 1 inch square foam to seal around the front of the airbox and trimmed 4 inches off the bonnet rubber, worked great. No need for a powa duct.

I just fitted an intake on an M35 yesterday, I used some 1 inch square foam to seal around the front of the airbox and trimmed 4 inches off the bonnet rubber, worked great. No need for a powa duct.

got a pic?

Nub question, but how do you remove the front section of the air box to replace the filter?

I've taken off the front 'lip' duct, unbolted the airbox itself (10mm bolt on the right), detached what I presume is the airflow meter and unclamped the rubber hose from the back of the box.

But the air box is still attached to something underneath it and there isn't enough room to get front of the air box off enough to swap the filters.

Suggestions?

Lovely job thanks Scotty.... :cheers:

post-20696-1261441284_thumb.jpg He even trimmed the rubber edge on the bonnet... post-20696-1261441298_thumb.jpg

Nicely showing off the new intake piping there too :santa:

Sound = 10/10

Performance = a bit subjective. Definitely dont think I've lost any performance. It does certainly feel like there is less restriction - particularly at low revs. More kw? I dont know. Even if there was, it would be very slight. I just love the sound :)

Yes the pick up is much better than previously, so fuel consumption not an issue, just enjoying it...

But going down to the Valley at the weekend so will see how it does then..

So have you noticed a difference Nick?

Or are you still learning how to drive it economically?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...