Jump to content
SAU Community

Recommended Posts

  • Replies 129
  • Created
  • Last Reply

Top Posters In This Topic

I am thinking I will go the RDA slotted rotors as mentioned above plus the QFM HPX pads.

Is anyone else running that combo? I would just go RDA pads green stuff), but a few people on here have said they aren't that good.

Then again, a mechanic I was going to get to do the install said the QFM pads are no good..... He said they need to get real warm to work ? ? ?

So I have no idea.

I won't be doing any track work or super heavy driving so I reckon the above combo should be good.

I got hpx on standard rotors. Work from cold. Not much heat needed. A1's need more heat but from what I've felt not much more.

I think the AR1M's are tough on rotors if not up to temp. I'll be going with the HPX pads when I do my upgrade.

They are, but they still work better than the EBC reds I had, even when stone cold. When they heat up (after one application) they are exceptional. My disks havent worn much at all in the short time I have had them on, I will let you know how they go but I wont be expecting 10 years out of them.

Im sure the A1RM's are much harder on disks when they are hot though, the noise they made on the disk sounded like an angle grinder when I stomped on them. lol.

Go the HPX's if you don't drive hard and run stock power though.

They are, but they still work better than the EBC reds I had, even when stone cold. When they heat up (after one application) they are exceptional. My disks havent worn much at all in the short time I have had them on, I will let you know how they go but I wont be expecting 10 years out of them.

Im sure the A1RM's are much harder on disks when they are hot though, the noise they made on the disk sounded like an angle grinder when I stomped on them. lol.

Go the HPX's if you don't drive hard and run stock power though.

what do you mean, i have the hpx and slotted rotors and they work better than expected at my power

Sweet.

I will have stock power for a little while yet..

Still have to get:

boot mat (don't laugh, I know its not an upgrade but still a few $)

Brake upgrade (RDA slotted + QFM HPX pads)

BC Suspension

Rims and Tyres.

Then Intercooler/exhaust etc.

Of course, this is all pending approval from the Minister for Finance!

Huh? I am...I'm looking at aftermarket pads for them (the fronts) though...

Not sure how good the OEM Brembo pads are...probably nothing special?

oh. honestly after seeing scotts A1RM's in the GTR brakes, i was impressed!

seeing as they are locally sourced, and cheap as poo. I would be looking at them.

and they have em available on hand so you walk in and grab em and leave - but thats my opinion.

RDA Standard Rotors with custom slotting (curved slots which do not go to end of rotors) and dimples (as per RDA Gold Passivated Turbo Grooved Sports Rotors). Combined them with full set of Dixcel High Performance Street Pads ex Japan. What a difference to the standard brakes...Very happy :thumbsup:

RDA Standard Rotors with custom slotting (curved slots which do not go to end of rotors) and dimples (as per RDA Gold Passivated Turbo Grooved Sports Rotors).

Whats the theory with the custom slots? Whats the benefit from curved slots which dont go to the end of rotors?

I guess dimples are a good compromise over cross drilled? Dont crack?

Curved slots look cooler than straight ones. Ones that end before the edge are designed to reduce cracking (so they say). Cross drilled ones crack. No idea what the dimples are for if you have slots. Cross drilled are supposed to aid cooling and/or let gasses escape- dimples wouldn't do that. Slots themselves are useful in getting rid of gases, keep pads clean get rid of water.

I live in East Bentleigh, but can travel....

I need 350z brembo compatible front slotted rotors.

PM me if you need to...:thumbsup:

Scotty had a look at them and the front rotors were so rusted they are crumbling away :unsure:

Edited by ironpaw

Our pricing on M35 rotors is:

Non Brembo

Front, $79 each for standard, or $249 for a pair of slotted

Rear, $69 each for standard, or $219 for a pair of slotted

Brembo

Front, $119 each for standard, or $309 for a pair of slotted

Rear, $119 each for standard, or $309 for a pair of slotted

As always, if you see them cheaper elsewhere we'll see what we can do, or a package price with pads etc.

Our pricing on M35 rotors is:

Non Brembo

Front, $79 each for standard, or $249 for a pair of slotted

Rear, $69 each for standard, or $219 for a pair of slotted

Brembo

Front, $119 each for standard, or $309 for a pair of slotted

Rear, $119 each for standard, or $309 for a pair of slotted

As always, if you see them cheaper elsewhere we'll see what we can do, or a package price with pads etc.

What kind of price on 370Z rotors? I'm working on something at the moment...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
×
×
  • Create New...