Jump to content
SAU Community

Recommended Posts

Great work on further weigh reduction.

I have a question for you...

How do you wash it without destroying the hard work Allison has put into the 'art'?

Only asking cos I don't think you've taken photos when the car's dirty.

Great work on further weigh reduction.

I have a question for you...

How do you wash it without destroying the hard work Allison has put into the 'art'?

Only asking cos I don't think you've taken photos when the car's dirty.

pretty sure he sprayed clear coat over the artwork.

With headlights, if you want em to come out crystal clean, you can sand em back with 800 grit sand paper (wet and dry), then 1000, then 1500 then 2000. Make sure you spend a while on each grit and get an even surface finish. Then either spray clear coat over em, or polish them up with some plastic polish or metal polish. They come up brand new :)

Edited by SkyHi_33
Great work on further weigh reduction.

I have a question for you...

How do you wash it without destroying the hard work Allison has put into the 'art'?

It's clearcoated courtesy of the Lost Birds Paint Shop... aka me. haha.

pretty sure he sprayed clear coat over the artwork.

With headlights, if you want em to come out crystal clean, you can sand em back with 800 grit sand paper (wet and dry), then 1000, then 1500 then 2000. Make sure you spend a while on each grit and get an even surface finish. Then either spray clear coat over em, or polish them up with some plastic polish or metal polish. They come up brand new :)

How powerful of a buffer would I need? The one I have now is a $30 on/off thing. Doesn't spin up that fast, so I'm wondering if it would do the trick.

Spend every day on Yahoo auctions and try and get some S3 Xenon lights for a good price, it really needs them now!

I can't find them for anything I'm willing to pay. lol. We have UPGarage here in japan, or "U"sed "P'arts Garage and they always have some for sale. It's a ntionwide network of stores that will ship to your local store. the last set they had was brand new in the box still for about 1750 AUD. no thanks! you can use the search box to look for whatever. just type R32 R33 or R34 and see what they have. or type RB26DETT :D

UPGarage

Edited by istdercollen
How powerful of a buffer would I need? The one I have now is a $30 on/off thing. Doesn't spin up that fast, so I'm wondering if it would do the trick.

I did mine by hand, sanded and polished... ill try get you some pics.

My female friend thought shed touch up my old matte black front bar and got over spray all over the headlights, so we grabbed some thinners to wipe it off and it completely frosted em up. I used the technique mentioned above and they came up almost brand new!

It's clearcoated courtesy of the Lost Birds Paint Shop... aka me. haha.

Ah, I thought you haven't clear coated the car yet.

I can't find them for anything I'm willing to pay. lol. We have UPGarage here in japan, or "U"sed "P'arts Garage and they always have some for sale. It's a ntionwide network of stores that will ship to your local store. the last set they had was brand new in the box still for about 1750 AUD. no thanks! you can use the search box to look for whatever. just type R32 R33 or R34 and see what they have. or type RB26DETT :D

UPGarage

This price is pretty cheap for brand new I remember someone in Oz asking $3k AUD for ok condition pair... I'd grab them if I were you and I think Just Jap in Sydney is asking at least $3k for new pair.

next chance i get I will be all over it!

Weight update...

Removed rear seat and rear seat safety belts for 31 pound/14.1kg reduction.

Stock Trunk Carpeting - 11.5lbs/5.2kg

Stock Floor Mats - 13.0lbs/5.9kg!!

Stock Jack/Tire Iron - 4.5lbs/2.05kg

Stock Spare Tire - 34.4LBSSSS/15.6kg

Nissan Air Purifier,sound deadening behind back seat, car jack - 9 lbs/4.1kg

metal plate behind the back seat - 6.4 pounds/2.9kg

Stock suspension 57.8lbs/26.3kg and HKS Hipermax 47.0/32.3kg - 10.8lbs/6kg net loss

door panels 14lbs/6.35kg

carpet and various pieces of plastic 16.2/7.3kg

Center console 7.6lbs/3.5kg

passenger seat 34lbs/15.4kg (with rail attached)

Difference in test pipe/cat 6lbs/2.7kg

new seat/rail vs old seat/rail 5lbs/2.3kg

dash stripped to shell - 3lbs/1.36kg

difference in exhausts 24.2lbs/11kg

all sound deadening 12lbs/5.5kg

radiator and fan 15lbs/6.8kgs

AC/Heater stuff behind dashboard 21lbs/9.5kg

=

270.4 pounds/126.6kgs

Stock R33 GT-R 3388lbs/1540kg

Lost Birds R33 3109.4lbs/1413.4kgs.

Just gonna keep it updated so that I have a record somewhere of it. should be below 1400kg before the end of the week as the compressor and AC lines are still attached, along with some other stuff coming out. also did some work on the seat and it's back another 8cm and down another 2cm. I'm 1.91m tall and my eyes are now level with the top of the dashboard, which by the way makes the car incredibly difficult to park.

Edited by istdercollen
  • 1 month later...
not sure if this has been posted but it looks like its catching on.

Linky

yes i've seen that, ive gotta say i like the skyline better. the lambo's graphics look a bit mindless to me and a bit cluttered. the r33's got some form and elegance to it. if it makes sense.

Edited by alex182
  • 3 weeks later...
  • 4 months later...

very good read.. awesome work by Allison mate.. huge dedication there

UPDATE: Went to Mine's today. New engine going in this week, as long as I can find the headers and outlet pipes I want in time, otherwise next week. MINE'S POWERRRRRRR!

Well, the short story is, a connecting rod bearing said goodbye to me. The other short story is, I didn't know the ECU installed in my car has no Rev Limiter. 8600 RPMs sounds awesome, but I guess it didn't help keep my engine alive. Mine's are really good people. They gave me a tour of the whole shop. They have 15 RB26s sitting on pallets ready to go. He said it would take 3 days to turn it around once I drop the car off. I have to go find some bigger turbos myself though, as they pretty much only deal R35 parts these days (as far as GT-Rs go). Pics etc. will come!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...