Jump to content
SAU Community

Recommended Posts

I saw a thread a while ago from Sydneykid (& others) that mentioned filling your catch-can with steel-wool (in a stocking) to slow down air speed (allowing the oil vapor time to drop from the air). I have recently fitted a catch-can so decided to do this...

However with my CC design the inlet/outlet are right next to each other, near the very top of the can & it only has a very small hole.

I assumed that there was no point having steel-wool down the bottom of the can when air is entering/exiting at the top so have put in HEAPS of steel-wool scourers to fill up the can as much as possible. The only thing is, as the hole on top is so small they have sort of compressed & are VERY tightly packed in there.

I am getting a bit worried that I will be "slowing down" airflow too much (almost blocking flow) as I removed both hoses before & blew through the CC & blowing as hard as I can into one hose there is sweet-FA air coming out the other!

However I must say, I never blew through the CC before it had steel-wool in it so dont really have anything to compare to. Maybe the can itself causes a slight restriction?

Am hoping to go & get car tuned on Saturday so need to sort this out tomorrow.

Will try & get some steel-wool out tomorrow but am wondering otherwise will this be ok?

Due to the small hole don't know how much luck I'll have removing it...

How tightly have other people packed theirs? (who have done the same thing)

Edited by wlspn
Link to comment
https://www.sau.com.au/forums/topic/309732-steel-wool-in-catch-can/
Share on other sites

Your call but some kind of stainless steel I reckon would be better because it won't corrode and fall to bits .

A .

Do you mean using the steel-wool? I am not talking about the little tiny ones that leave splinters & have pink stuff on them...

These are a stainless-steel (or at least so they say) scourer.

i had a stocking full of stainless steel wool inside but ive removed it. actualy i had about 5 stockings wrapped around the wool. i was paranoid about getting steel wool inside my engine incase the stocking failed (they are bloody thin!) thats why i removed the stocking n wool altogether. is a catch can thats not venting useless without it?

It is a bit of a concern that they're so thin isn't it... How much steel-wool were you using? Heaps or just a little? According to Sydneykid (who knows what he's talking about) if the catch-can isn't baffled you should use steel-wool or it's not doing much as oil vapors are still getting through. Am sure some people would disagree though...

The stainless scourers I sourced from bunnings, I put 6 in the drift can I got. They increase the surface area of the can to help with separating the oil and water out of the air.

Getting a custom can made is great for tight places. Just make sure you put a tap on the bottom with a hose to drain the oily water out easily.

Steel wool in the catch cans are only beneficial when they are being used as an oil/air separator (i.e. they are just plumbed inline with a factory breather setup).

If it's for your track car and used as a catch can, then there is no need to fill the can with anything and just run it atmo.

You don't need to "pack" the CC. All the steel wool is there for is to provide a surface that the oil vapour can condense onto.

OK, but I assume the air should flow through the steel wool?Which is why I put a lot in to try & build the steel-wool up to the height of the inlet/outlet...

Steel wool in the catch cans are only beneficial when they are being used as an oil/air separator (i.e. they are just plumbed inline with a factory breather setup).

If it's for your track car and used as a catch can, then there is no need to fill the can with anything and just run it atmo.

This is being used as an oil/air seperator for a street car...

I have played around with the stainless steel wool in the stocking approach. I have found that the air travels through the stainless steel wool fine...but when placed in the stocking it restricts the airflow back out of the catch can.

However, this depends on how tight you stretch the stocking....obviously the more the stocking is stretched, the greater the airflow through it...but no doubt still has an effect on airflow.

Edited by juggernaut1

No doubt it will have some effect on airflow but I don't imagine this is too much of a concern unless you're actually causing a major restriction from the catch-can to intake, which could cause high crankcase pressure. Think this is what mine will do...

Going to see if I can get any steel-wool out. Bloody hope so!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...