Jump to content
SAU Community

Recommended Posts

Ok today was suposed to be a good day, i got all my parts i was missing and i started cranking on the motor nice and early, but about an hour into it while torqueing one of the bolts to the rear main seal it snaps effortlessly. ok no big dead i have extracted tons of bolts, so i drill it out perfectly center and procede to use my extractor which than snaps in the bolt which is inside the block. i tried almost every bit known to man and nothing grabs it,, i bought a super expensive industrial bolt out but i cannot not drill into the old bolt out. the snap is flush with the block so i cannot try to grip it and take it out. my ONLY option is to drill and extract. does anyone know a good drill bit that i can use to get this out. i am soo f***ing mad i thought i was gunna slam motor on the hood of the chassis in a fit of rage. has this happened to anyone else ? i know better than to ask this, but has anyone else only used 5 of the 6 bolts that hold the seal in place. I am pretty sure only using 5 bolts would not be too bad. i looked at it and it dosent hold see any physical stress, and its rtv sealed. any input. after i messed around with it, i am sure it can onlybe extracted by a machine shop....

Link to comment
https://www.sau.com.au/forums/topic/310574-broken-stud-on-rear-main-seal/
Share on other sites

good work breaking that one! I've seen plenty of main rear seal bolts stripped but normally the ones from the sump where they thread into the alloy rear seal housing. Anyway I'd probably leave it, if it leaks like a bastard some how (unlikely) you can always take the flywheel off and get to it in the car

I guess you weren't using a torque wrench...these are only m6 bolts right?

USA - do you have spark erosion guys over there? They seem to be able to get the impossible studs out..............not sure about ezi outs though, they are tough metal?

Otherwise a Dremel with some tungsten bits and be prepared to break a few, it won't be easy thats for sure.

Carbon tipped drill piece for drilling stainless, BUT you HAVE to drill freaking slowly (Like slowest speed possible!) or you will munt the drill bit.

Carbon tipped drill pieces are used on stainless and other very hard metals.

high speed dentst drill and a carbide bit or hers one for you weld a nut the same diameter as the origonal bolt head onto the shank,the nut will almost shutter the weld pool so it doesent contact the rest of the casting,ive done this many times before

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...