Jump to content
SAU Community

Recommended Posts

Cars booked in for 100k service / cam gears to go on woo just went to racepace local to me and they know there Rs

Billy, Kris told you so :P

I'm at 501 pages, you gotta up the posts per page :thumbsup:

Anyone know a cop-free safety zone for running in figure 8s?

Nice!!!

My 2 way is fairly clunky and kinda worrying in the wet haha

Is it a KAAZ? Did you put it in recently? 2 ways tend to clunk alot anyway, but it's supposed to get better after the first oil change. Have them in the race cars and they are great on track, but my 'line is also a daily and 1.5 seemed a good compromise.

Birds where'd you get the diff from?

eBay, friend.

Anyone know a cop-free safety zone for running in figure 8s?

Is it a KAAZ? Did you put it in recently? 2 ways tend to clunk alot anyway, but it's supposed to get better after the first oil change. Have them in the race cars and they are great on track, but my 'line is also a daily and 1.5 seemed a good compromise.

eBay, friend.

Try Laverton if your in the West :)

Its Cusco, i just put it in on Saturday :) Once its warm its good. In the dry I can deal with it easy but in the wet its just dangerous, especially with cheap shitty tyres.

Have Fun haha

A little boy wakes up three nights in a row when he hears a thumping sound coming from his parents bedroom. Finally, one morning he goes to his mom and says, "Mommy, every night I hear you and daddy making noise and when I look in you're bouncing up and down on him."His mom is taken by surprise and says. "Oh ... well I'm bouncing on his stomach because he's fat and that makes him thin again."The boy says, "That won't work."His mom says, "Why?"The boy replies. "Because the lady next door comes by after you leave each day and blows him back up!"

So, thinking of an Evo V, VI or VI TME. Can get most under $20k too which is a plus. Hmmm....

V's are the best of the 3

At the heart of every Evo driver this is a craving for Banana. End of story.

post-59171-0-22654100-1298860510_thumb.jpg

That beeing said, I can't see the point in a TME over the 6. You're going to ditch the dampers and springs, tune etc etc etc

Getting hold of a TME turbo isn't that hard if you want the pimp Ti turbine wheel etc

TME isnt all its made out to be, your better off getting a 9RS turbo, can hold antilag etc as well... much stronger

bangs gets wayyyyyyyyyy to many views considering his lack of talent, it is LOL worthy thats all i could put it down to.

i wonder which fools tell him its a good idea for him to make that shit? like really... they aint yo freinds buddy

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...