Jump to content
SAU Community

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

I have recently seen a matte black R35 in Melbourne. Does anyone know who can do this ?

Nearly any good panel shop can do this for you - it's going to be costly - but you will need to strip the GTR back to factory coat and respray as necessary.

As far as I know - the R35 GTR does not come in Matt-black - please correct if I am wrong though.

vinyl wrap will look about as good as home tint jobs do after a while

Is this a fact?

I'm asking because I have no idea and have never seen a vinyl wrapped car in the flesh. I have considered doing this to my own car but have always wondered how durable a vinyl wrap would be in the harsh Australian sun over time.

Can anyone provide pictures of a vinyl wrapped car and then show it 1-2 years later and 5 years later if possible? A car that actually gets driven too, and not just rolled out for display at car shows.

vinyl wrap will look about as good as home tint jobs do after a while

wow such an unsupported comment to make.

And even if they do turn shit after a while how hard is it to take it off and reapply? Not very hard at all depending on what material they use to contact it to the body.

You think that looks good? I saw the same thing done to a Lambo Murcielago in Lucerne Switzerland last year, it was the bomb batmobile style

Hey I saw that very car today on Ferntree Gully road at about 10.30am!!

To be honest, I rprefer the black shiny factory paint, but it certainly did look tough in the matt, maybe this particular car was a bit too grey, if it had more black to it, like the photo LSX-438 had posted perhaps?

BTW this is only the 3rd GT-R I have ever seen in the metal...and it has been said before, this car has REAL supercar presence on the road!

I have recently seen a matte black R35 in Melbourne. Does anyone know who can do this ?

Contact Nick at Exotic Kustoms, 0397735944

it is a vinyl wrap, not that expensive, lasts up to 5 years, any damaged sections can be replaced, can be done in any colour available.

Hi Dave,

I would like to know if it is a paint job or vinyl wrap?

If it is a wrap where can I see one in the flesh? What is the cost of doing one?

Thanks.

It is a wrap, done by Exotic Kustoms in Carrum Downs. It cost about $3750 I think.

Ring Nick on 97735944.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...