Jump to content
SAU Community

Recommended Posts

why am i not surprised! im hearing alot of bad stuff these days. Apart from their fan boys that is

They seem to get Nitto running pretty well but, struggled to get my tune right. But they are really good to get a long with as guys and hang out with. Tuning just wasnt to my liking. and yes they are a bit on the expensive side.

They seem to get Nitto running pretty well but, struggled to get my tune right. But they are really good to get a long with as guys and hang out with. Tuning just wasnt to my liking. and yes they are a bit on the expensive side.

im not a fan at all...but thats another story! ill give em a call and find out a 6466 .84 is?

lol all good. I gave them a buzz and they are ringing me back with a price.

I must admit their run of 9.6 @160mph seems slow considering the trap speed. JW Automotive work on an R32 that did around the 9.4 or 9.2 mark @ 149mph

  • Like 1

lol all good. I gave them a buzz and they are ringing me back with a price.

I must admit their run of 9.6 @160mph seems slow considering the trap speed. JW Automotive work on an R32 that did around the 9.4 or 9.2 mark @ 149mph

This. high trap speed for no speed. Should be low 9s easily, but then dont even get me started on these guys lol

they will more than likely run with the excuses of bad tyres and wheel spin again

or they were on run in tune of 938whp and 34psi of boost

Edited by Frosty

least they have run a 9 now.

Watching the runs though, there is too much engine for the chassis setup, its all over the shop, bobbing and weaving etc.

If they get that sorted instead of throwing more power at it it will be quick

its never going to be anything other than a dyno queen

Its a 9 second street car - that's definitely more than just a dyno queen, mid 9s is serious business even if it isn't as quick as it could be.

Its a 9 second street car - that's definitely more than just a dyno queen, mid 9s is serious business even if it isn't as quick as it could be.

Its far from a dyno queen, its gets used and abused :yes:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...