Jump to content
SAU Community

Recommended Posts

Hi,

I hope I don't annoy too many people. I have searched through a few threads now and I haven't been able to get a clear answer. I want to know what offset of wheel looks good on a R32 GTR. I DON'T LIKE THE SUNKEN LOOK.

-Is 22 ok for a GTR or is that more for the R32 GTST?

-Can anyone give me a list of good offsets to be used. (I don't want to use spacers)

Thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/313971-off-sets-im-confused/
Share on other sites

Hi,

I hope I don't annoy too many people. I have searched through a few threads now and I haven't been able to get a clear answer. I want to know what offset of wheel looks good on a R32 GTR. I DON'T LIKE THE SUNKEN LOOK.

-Is 22 ok for a GTR or is that more for the R32 GTST?

-Can anyone give me a list of good offsets to be used. (I don't want to use spacers)

Thanks in advance.

Depends on the width of the rim big guy. 22 offset on a 9" rim is different to 22 offset on a 10" rim.

For what its worth, I run 18x10" +20 offset. A +22 offset on a 10" rim would put the outside of the rim 2mm further under the guard. (and yep, a 10" rim with +22 offset on a GT-R would look tuff)

yes it depends on the width of the rim...

+22 is an acceptable, medioka fitment for GTR's... its a tough fitment for gtst's though.. for a really flush/slightly outside the guards fit on a GTR, look around for something around +15.

i have a set of 17x9 + 25 and 17x9.5 + 25.. even though its only 12mm wider.. the 9.5's sit much further outside the guards than the 9's do.. i could pull off the 9's even with wide tyres, whereas the 9.5s i need stretched tyres to fit.

offset is not that hard to work out... its only when you throw different widths into the mix that it becomes difficult.

i wouldnt look at anything smaller than 9.5" and with more offset than +20.

and remember that wheel widths are measured bead to bead... not edge to edge.. so a 9.5" rim is usually 10" edge to edge... but that all depends on the brand of wheel and the type of lip they use.

Hi,

Thanks to everyone who has posted in.

Will the eneki rpo1 17X9 22 sit flush with the guard. I don't want a rim that sits outside the guard. If these are no good can somebody recomend a forged alloy rim that can house 6 pot calipers and sit flush with the guards.

Thanks

Hi,

Thanks to everyone who has posted in.

Will the eneki rpo1 17X9 22 sit flush with the guard. I don't want a rim that sits outside the guard. If these are no good can somebody recomend a forged alloy rim that can house 6 pot calipers and sit flush with the guards.

Thanks

A 17*9" +22 rim is a very good fit for an R32 GTR. I have that size on mine. They are CE28's which clear an F40 calliper on a 324 rotor.

The thing you have to understand is that the amount of camber you run will have a big impact on how flush the top of the tyre sits to the guard. You can make just about anything fit if you run stupid amounts of negative camber.

Also it is common for the rear guard lip to contact the tyre if the ride height is low - a 255/40 rear tyre in a Briudgestone RE55 will usually do so.

As far as calliper clearance unless you can get a diagram of the wheel/calliper the only way to confirm it is to see it. Enkei are usually pretty good on the clearance but it can depend on the calliper alot too.

post-5134-1270092990_thumb.jpg

17X9 +22 will look fine. they certainly won't look 'sunken' (lol) at all. ekei's make a good wheel and like djr81 said they generally (in their racing type wheels) have quite generous calliper clearance too.

I have 18x10+13 and I am having troubles making them fit properlly with guard issues but will look super tuff once I can get them to fit on my 32-R.

18x10+20 would be the perfect offset with minimal headf**ks lol

I have 18x10+13 and I am having troubles making them fit properlly with guard issues but will look super tuff once I can get them to fit on my 32-R.

18x10+20 would be the perfect offset with minimal headf**ks lol

At some stage a historian will be able to pin point the exact time owning a GTR turned into a pissing competition about how much rim/tyre/offset could be shoved under the guards. :(

You are having troubles fitting the rims because they have too much offset & are an half an inch to an inch wider than they need to be.

Not having a go at you but I get sick of people trying to talk up wheel tyre sizes to the detriment of suspension geometry & handling - not to mention tyre life.

17X9 +22 will look fine. they certainly won't look 'sunken' (lol) at all. ekei's make a good wheel and like djr81 said they generally (in their racing type wheels) have quite generous calliper clearance too.

what he said :worship:

handy tool for this purpose...

http://www.1010tires.com/WheelOffsetCalculator.asp

Edited by WHITE R32
Hi,

I hope I don't annoy too many people. I have searched through a few threads now and I haven't been able to get a clear answer. I want to know what offset of wheel looks good on a R32 GTR. I DON'T LIKE THE SUNKEN LOOK.

-Is 22 ok for a GTR or is that more for the R32 GTST?

-Can anyone give me a list of good offsets to be used. (I don't want to use spacers)

Thanks in advance.

your not the only one. i been searching and reading pages and pages. still not with it. even with the online tools. lol. is the number higher meaning it sticks out more? or vice versa? :S same as you, i dont want the wheels to sit in, but yet again, dont want the stupid vip look.

i been looking for wheels online, but i think im just gonna have to find a tyre shop that already knows whats a good fitment.

trying to source 18 or 19" on a r33 gtst.

A 17*9" +22 rim is a very good fit for an R32 GTR. I have that size on mine. They are CE28's which clear an F40 calliper on a 324 rotor.

The thing you have to understand is that the amount of camber you run will have a big impact on how flush the top of the tyre sits to the guard. You can make just about anything fit if you run stupid amounts of negative camber.

Also it is common for the rear guard lip to contact the tyre if the ride height is low - a 255/40 rear tyre in a Briudgestone RE55 will usually do so.

As far as calliper clearance unless you can get a diagram of the wheel/calliper the only way to confirm it is to see it. Enkei are usually pretty good on the clearance but it can depend on the calliper alot too.

not having a go at you... as your gtr looks very tidy... but i would consider that sunken... not flush.. if that is the fit the OP is after... than all good and well... but flush is only achievable with stretched tyres, i know you are anti stretched tyres, but i approve of the stretch... so it is up to the OP.. if he wants a fitment like yours, then +22 will be fine.. but if he considers that sunken, then he'll need something like +15ish... with some 235's fitted with some stretch.

not having a go at you... as your gtr looks very tidy... but i would consider that sunken... not flush.. if that is the fit the OP is after... than all good and well... but flush is only achievable with stretched tyres, i know you are anti stretched tyres, but i approve of the stretch... so it is up to the OP.. if he wants a fitment like yours, then +22 will be fine.. but if he considers that sunken, then he'll need something like +15ish... with some 235's fitted with some stretch.

Well if you have a closer look you will notice the front end is running alot of -ve camber plus a bunch of other non standard bits. About four degrees. I could easilly make it look more "flush" by winding some out.

Which was my point, really. You need to know both the wheel/tyre size, the ride height & the amount of -ve camber. They are all inter related.

Best thing to do is to try a rim.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
×
×
  • Create New...