Jump to content
SAU Community

Off Sets I'm Confused.

iwantagtr
 Share

Recommended Posts

iwantagtr Rising Star

iwantagtr

Posted
Posted

Hi,

I hope I don't annoy too many people. I have searched through a few threads now and I haven't been able to get a clear answer. I want to know what offset of wheel looks good on a R32 GTR. I DON'T LIKE THE SUNKEN LOOK.

-Is 22 ok for a GTR or is that more for the R32 GTST?

-Can anyone give me a list of good offsets to be used. (I don't want to use spacers)

Thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/313971-off-sets-im-confused/
Share on other sites
R32 TT Mentor

R32 TT

Posted
Posted
Hi,

I hope I don't annoy too many people. I have searched through a few threads now and I haven't been able to get a clear answer. I want to know what offset of wheel looks good on a R32 GTR. I DON'T LIKE THE SUNKEN LOOK.

-Is 22 ok for a GTR or is that more for the R32 GTST?

-Can anyone give me a list of good offsets to be used. (I don't want to use spacers)

Thanks in advance.

Depends on the width of the rim big guy. 22 offset on a 9" rim is different to 22 offset on a 10" rim.

For what its worth, I run 18x10" +20 offset. A +22 offset on a 10" rim would put the outside of the rim 2mm further under the guard. (and yep, a 10" rim with +22 offset on a GT-R would look tuff)

NZM.031 Grand Master

NZM.031

Posted
Posted

yes it depends on the width of the rim...

+22 is an acceptable, medioka fitment for GTR's... its a tough fitment for gtst's though.. for a really flush/slightly outside the guards fit on a GTR, look around for something around +15.

i have a set of 17x9 + 25 and 17x9.5 + 25.. even though its only 12mm wider.. the 9.5's sit much further outside the guards than the 9's do.. i could pull off the 9's even with wide tyres, whereas the 9.5s i need stretched tyres to fit.

offset is not that hard to work out... its only when you throw different widths into the mix that it becomes difficult.

i wouldnt look at anything smaller than 9.5" and with more offset than +20.

and remember that wheel widths are measured bead to bead... not edge to edge.. so a 9.5" rim is usually 10" edge to edge... but that all depends on the brand of wheel and the type of lip they use.

iwantagtr Rising Star

iwantagtr

Posted
  • Author
Posted

Hi,

Thanks to everyone who has posted in.

Will the eneki rpo1 17X9 22 sit flush with the guard. I don't want a rim that sits outside the guard. If these are no good can somebody recomend a forged alloy rim that can house 6 pot calipers and sit flush with the guards.

Thanks

djr81 Grand Master

djr81

Posted
Posted
Hi,

Thanks to everyone who has posted in.

Will the eneki rpo1 17X9 22 sit flush with the guard. I don't want a rim that sits outside the guard. If these are no good can somebody recomend a forged alloy rim that can house 6 pot calipers and sit flush with the guards.

Thanks

A 17*9" +22 rim is a very good fit for an R32 GTR. I have that size on mine. They are CE28's which clear an F40 calliper on a 324 rotor.

The thing you have to understand is that the amount of camber you run will have a big impact on how flush the top of the tyre sits to the guard. You can make just about anything fit if you run stupid amounts of negative camber.

Also it is common for the rear guard lip to contact the tyre if the ride height is low - a 255/40 rear tyre in a Briudgestone RE55 will usually do so.

As far as calliper clearance unless you can get a diagram of the wheel/calliper the only way to confirm it is to see it. Enkei are usually pretty good on the clearance but it can depend on the calliper alot too.

post-5134-1270092990_thumb.jpg

Beer Baron Grand Master

Beer Baron

Posted
Posted

17X9 +22 will look fine. they certainly won't look 'sunken' (lol) at all. ekei's make a good wheel and like djr81 said they generally (in their racing type wheels) have quite generous calliper clearance too.

Weezy Grand Master

Weezy

Posted
Posted

I have 18x10+13 and I am having troubles making them fit properlly with guard issues but will look super tuff once I can get them to fit on my 32-R.

18x10+20 would be the perfect offset with minimal headf**ks lol

djr81 Grand Master

djr81

Posted
Posted
I have 18x10+13 and I am having troubles making them fit properlly with guard issues but will look super tuff once I can get them to fit on my 32-R.

18x10+20 would be the perfect offset with minimal headf**ks lol

At some stage a historian will be able to pin point the exact time owning a GTR turned into a pissing competition about how much rim/tyre/offset could be shoved under the guards. :(

You are having troubles fitting the rims because they have too much offset & are an half an inch to an inch wider than they need to be.

Not having a go at you but I get sick of people trying to talk up wheel tyre sizes to the detriment of suspension geometry & handling - not to mention tyre life.

WHITE R32 Grand Master

WHITE R32

Posted
Posted (edited)
17X9 +22 will look fine. they certainly won't look 'sunken' (lol) at all. ekei's make a good wheel and like djr81 said they generally (in their racing type wheels) have quite generous calliper clearance too.

what he said :worship:

handy tool for this purpose...

http://www.1010tires.com/WheelOffsetCalculator.asp

Edited by WHITE R32
Jaysiin Enthusiast

Jaysiin

Posted
Posted
Hi,

I hope I don't annoy too many people. I have searched through a few threads now and I haven't been able to get a clear answer. I want to know what offset of wheel looks good on a R32 GTR. I DON'T LIKE THE SUNKEN LOOK.

-Is 22 ok for a GTR or is that more for the R32 GTST?

-Can anyone give me a list of good offsets to be used. (I don't want to use spacers)

Thanks in advance.

your not the only one. i been searching and reading pages and pages. still not with it. even with the online tools. lol. is the number higher meaning it sticks out more? or vice versa? :S same as you, i dont want the wheels to sit in, but yet again, dont want the stupid vip look.

i been looking for wheels online, but i think im just gonna have to find a tyre shop that already knows whats a good fitment.

trying to source 18 or 19" on a r33 gtst.

NZM.031 Grand Master

NZM.031

Posted
Posted
A 17*9" +22 rim is a very good fit for an R32 GTR. I have that size on mine. They are CE28's which clear an F40 calliper on a 324 rotor.

The thing you have to understand is that the amount of camber you run will have a big impact on how flush the top of the tyre sits to the guard. You can make just about anything fit if you run stupid amounts of negative camber.

Also it is common for the rear guard lip to contact the tyre if the ride height is low - a 255/40 rear tyre in a Briudgestone RE55 will usually do so.

As far as calliper clearance unless you can get a diagram of the wheel/calliper the only way to confirm it is to see it. Enkei are usually pretty good on the clearance but it can depend on the calliper alot too.

not having a go at you... as your gtr looks very tidy... but i would consider that sunken... not flush.. if that is the fit the OP is after... than all good and well... but flush is only achievable with stretched tyres, i know you are anti stretched tyres, but i approve of the stretch... so it is up to the OP.. if he wants a fitment like yours, then +22 will be fine.. but if he considers that sunken, then he'll need something like +15ish... with some 235's fitted with some stretch.

djr81 Grand Master

djr81

Posted
Posted
not having a go at you... as your gtr looks very tidy... but i would consider that sunken... not flush.. if that is the fit the OP is after... than all good and well... but flush is only achievable with stretched tyres, i know you are anti stretched tyres, but i approve of the stretch... so it is up to the OP.. if he wants a fitment like yours, then +22 will be fine.. but if he considers that sunken, then he'll need something like +15ish... with some 235's fitted with some stretch.

Well if you have a closer look you will notice the front end is running alot of -ve camber plus a bunch of other non standard bits. About four degrees. I could easilly make it look more "flush" by winding some out.

Which was my point, really. You need to know both the wheel/tyre size, the ride height & the amount of -ve camber. They are all inter related.

Best thing to do is to try a rim.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      Chris' Toyota Mark ii JZX110

      By PranK · Posted

      This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • soviet_merlin
      Duncan's V37.......race car?

      By soviet_merlin · Posted

      Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • Murray_Calavera
      Jacks that fit under GTR lips that can reach the subframe?

      By Murray_Calavera · Posted

      My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Duncan
      Chris' Toyota Mark ii JZX110

      By Duncan · Posted

      Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
×
×
  • Create New...