Jump to content
SAU Community

Recommended Posts

Before you begin

=============

Nothing worse than starting a job and not having everything you need onhand before you begin! So therefore you will definitely need:

1x Socket set (and ratchet), with 10mm and 12mm sockets (most are 10mm)

1x long socket extender - definitely recommended. Makes thing *much* easier in spots, increased leverage to get stubborn bolts undone as well.

1x stumpy philips head - for the tight spaces and general screws

1x long philips head - when you need to get to a screw with a long reach

1x flat head - mainly for helping to pop stuff out.

1x adjustable wrench - for stubborn nuts, etc

1x water! :( Hard work, on a hot day can take a lot out of you, and this can be about a 6hour job (depending on whether you have done it before). Took me about 6 hours to get to the heater core, which is why i pulled it apart in the first place.

Before you begin tackling the main dash: Follow Pushead's guide to get the front facia off... here: http://www.skylinesaustralia.com/forums/sh...ead.php?t=31182

Then continue onto this one :)

Link to comment
https://www.sau.com.au/forums/topic/31550-removing-entire-dash-howto/
Share on other sites

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Gearshift Surround

================

1. Unscrew shiftknob, remove ashtray, and undo 2x screws behind. Rest is just clips. Unclip out:

2. Undo top facia screws. Lower scews connecting to centre console also need to be removed.

Stereo removal

=============

1. Undo top facia screws. Lower scews connecting to centre console also need to be removed.

2. Remove bottom four screws shown above to remove head unit. The whole bracket should slideout. Disconnect all connections to face unit. Fiddle with or replace stereo as necessary :(

then move onto...

Climate Control box

================

1. Remove top 2x screws in last pic after stereo has been removed. Unplug 2x plugs on back to remove control box completely.

mmmm...spaghetti! Its not quite as bad as it looks (really!)

Glovebox Removal

===============

1. Remove glovebox assembly, undo red circled screws and unclip green circled clips.

Trickiest one is the one bottom right, which you'll have to do with the glovebox open, and using a long philips head to get in there.

2. After that you'll have to kind of pop the clips out which attach to the upper part of the dashboard. I snapped one because its hard to do it without doing that but superglue will fix it.

3. You will need to undo the catch screws, as these also hold it in.

4. Carefully remove entire assembly and set aside.

http://www.skylinesaustralia.com/forums/at...tachmentid=9901

Below Steering wheel

================

1. Remove the bonnet popper. 2x screws as shown in pic #1.. should drop down as shown. Don't worry, won't spring back - can still pop the bonnet if needed at any time like that.

2. Remove screws as shown in pic #2. Unclip from position shown, breaking clips in process :( If they do like mine, just glue back up with superglue. Once you remove the plastic it should look like in pic #2)

3. Remove screw on right for main dash (pic #3)

RHS footwell plastic

===============

This is just to your left leg. Remove screws as shown, and drop down, or just remove if you don't have turbo timers, etc attached :(

A-pillar covers

===========

1. Drivers side is easy, as no handle to be unscrewed first. Unclip clips shown (pretty stubborn). May have to pop out the first bit of the quarter window plastic it sits under.

2. Remove a-pillar cover. Kind of sliding it out from where it meets the dash.

3. Do passenger side same, except you'll have to remove handle (2x screws under plastic caps). Use flat head to pop off caps.

Top vents and Sun sensor

===================

1. Use a flat head (as shown) to pop out the RHS vent

2. Reach out under the dash and popout the sun sensor. Disconnect it from its connector

3. This should make removal of the LHS vent easy. Which should now pop out.

4. Take random pick of surroundings (optional) :(

Dash main

========

Ok, here comes the final removal of the dash.

1. Remove steering wheel (if not done already). Mine was nice and simple, good ol' momo!

2. Remove top two screwbolts. Best to use a socket extender at angle into sunsensor hole, and corresponding hole on RHS.

3. Remove screws from bottom RHS and bottom LHS of dash, if not already

4. Remove centre nut (just above steering wheel)

You may also have to slip your car into 4th gear or so to get the gearshift out of the way to help you get the dash structure out.

This is it for the disassembly! Now to get that big chunk of plastic out...

5. Slowly remove entire dash by pulling forward, checking for any screws still holding it in that may have been left.

6. Angle up and I think its easiest to manuveur whole dash through passenger side. I managed to lift it out by myself without damage, but a helping hand could make it much easier. It weights about 8kg.

7. Stare in wonder with what lies beneath (last photo) :(

So that is pretty much it!

Reassembly is a reversal of the above process (i've always wanted to say that :()

Removing the full dash will allow you to get at a few useful things: main fan, airconditioning cooler, heater (and heater radiator) and the loom that goes through to the engine.

Nice thread this will get stickied. More people should take the time to do this! Well done. I always carry out complex repairs and wish i had got snap happy in the process!! however the how to install remote start paging alarms with boot release central locking , window roll up, sunroof closure etc etc would take way too long and give me nothing to do as a result!!! Keep up the good work! :(

Jay95R33: it looks worse than it is in the photo, plugs going everywhere - but generally a plug will only fit the one socket so its hard to get it mixed up putting all back together.

Autotrust: lol - i guess if you do it all the time like you it becomes 2nd nature. Still, there will always be a market for people to get others to do this sort of thing. I mean it takes hours, and unless you're really keen - who really does want to pull apart their car.

  • 2 months later...
  • 8 months later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...