Jump to content
SAU Community

Recommended Posts

we fixed the fitment difficulties. I reckon the fit is now 95% OEM. slight uneven panel gap near quarter panels, very acceptable

The front reinforcement bar needs to be cut to size at the ends to fit the bumper

intercooler shroud sits well around the intercooler, it would require trimming to fit your individual intercooler.

brake duct guides look to be very usable as I have mentioned previously. just need a solution at the rotor! we will be addressing this next.

The oil and tranny coolers need some tweaking of their brackets so that the coolers sit flush with the cutouts on either side, the effect when positioned right is excellent.

Overall I am very happy with the end product. If you are a track junkie then I reckon this bumper will be for you, I will however partially reserve judgement until I can investigate the brake ducting solution and its function out on the track. Also, if you are considering this bumper though you will need to budget for quite a lengthy install and some fabrication of the cooler brackets

this is a photo from the guys at the workshop. I will get some more detail shots soon.

gallery_56949_3818_93050.jpg

a few pics, car filthy but being in and out of the shop for ongoing mods means no time for cleaning! (reminds me of dirty dee of pootie tang fame!) will give it a wash before next track day

car with aeromotions r2.two, top racing bumper on and new ride height

gallery_56949_3877_12590.jpg

gallery_56949_3877_43335.jpg

Looks like you have put the car on just a little bit of a diet Mark !!. Car is looking mega tough mate will be good to catch up at the next track day I am planning on having my car out there for a bit of a shake down. You doing morning or afternoon session ?.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...