Jump to content
SAU Community

Recommended Posts

10 hours ago, r32-25t said:

The tomei manifolds are a waste of money due to the fact they crack, have seen factory manifolds that have been open up a little make over 600 Australian horsepower at the wheels

I didn't know Australian horsepower is its own thing and different from other standard measurements LOL

 

6 hours ago, Piggaz said:

Have done a back to back myself about 6 years ago. Took off a set (which was the second set in total) of Tomri manifolds and went back to tickled stock items. No difference at all. On top of that, the second set blew a hole in number 1 runner within 1,500 kms. They're garbage.

Put the money you save towards something useful, like an aftermarket front diff.

As for GT-RS's. No one would miss them if they wernt made anymore. 

I didn't know GT-RS has such bad reputation.  How about the -9's I am looking at?  I mostly cruise my R32, so I was told the GT-SS/-9's has the best low rpm response than any other turbos out there.

I also didn't know Tomei manifolds are such garbage.  I will see if I can get my stock manifolds ported to match Garrett's 38mm x 45mm port.

So how about Tomei's turbo elbow?  I have Reimax front pipe which is 60mm, same as Tomei's elbow.

I knew the front diff is a weak point, but I really didn't know there is aftermarket units available!  Is it an entire internal or just individual components to address the weak links?  

I have much to learn that's for sure.

Tomei as a brand make some good parts ie. oil pump, camshafts, cam gears.  But their manifolds (being made of stainless steel instead of cast iron) are prone to weakness, and their turbos (oil cooled only, instead of water and oil) leave room for much better improvements.

Some input as i am going through a very similar process at present.

Power

Garrett -9 are a well documented strong performer for a street car, combining them with;

Engine

- port-matched manifolds

- aftermarket turbo elbows (tomei or reimax are perfect)

- cam gears, will be the source of the power increase in your build.

- OPTIONAL - bigger airflow meters (Nismo) or deleted AFMs if

Exhaust

- enlarged front pipe (aka dump pipe)

- enlarged exhaust 3' or 3.5'

Fuel

- larger injectors, stock are approx 444cc, anything from 500-650 will match this sort of power level

- fuel pump (stock GT-R is 197lph, upgraded nismo 255lph is good, Walbro 255 also a good cost effective option)

Optional extras for smaller gains are; mid-size intercooler and entry level camshafts, however, they can delay response for the sake of peak power (especially if a big 100mm intercooler and big lift camshafts are used)

All of these are able to be done with the engine in the car, minimising on labour cost.

 

ECU

- If you have a stock ECU, work with your tuner to select an ECU and boost controller that they are familiar with to achieve the best result

- common aftermarket units include Apexi Power FC (budget) and Haltech Platinum Pro as the premium option (better fail safes, and much more tune-ability.)

Reliability;

If the motor is coming out of the car to be built, you have a few options in terms of amending a few of the factory flaws, as well as strengthening the internal components.

As a guide;

Head

- head refresh (mild port)

- enlarged drain return from the head to the sump

Block

- new bearings

- oil pump (few choices here, either forged gears in the OEM pump, or a aftermarket pump ie. Tomei, note if you are going with an larger pump like the Tomei, you will want an enlarged sump to accommodate for the additional flow)

- sump baffle

There is the option to go further with forged crank, piston, rods, rings and enlarged sump, however this does almost double the cost, for minimal benefit unless there is heavy track work and future plans for more power.

A good guide for a reliability build;

https://www.facebook.com/Tarmac-Solutions-Pty-Ltd-189006661230825/photos/?tab=album&album_id=418233531641469

Some good starting points for reading;

http://www.gtrusablog.com/2010/05/real-basics-nissan-skyline-gt-r-r32-r33.html

http://www.sau.com.au/forums/topic/429930-1994-r32-gtr-stock-to-~320kw/?page=1

Diffs;

I would probably leave this until you've been able to drive the car for a while, the R32 has mechanical diffs which are decent already compared to the R33 & R34 

Money is better spent on Suspension first, then brakes or diffs pending budget in my opinion.

 

All the best with the build., there is a lot of info out there, however it isn't all in one place which makes it a bit difficult to sift through.

 

Edited by squareznboxez
forgot the fueling upgrades for power build
  • Like 1
2 hours ago, TXSquirrel said:

I didn't know Australian horsepower is its own thing and different from other standard measurements LOL

 

 

2 hours ago, r32-25t said:

American dynos tend to read stupidly higher then ours and it's become a bit of a running joke 

 

Can confirm, Australian dynos read really low compared to most dynos around the world and while there are a lot of knowledgable and generally good dudes on here - the fact they have inconsistent and USUALLY low reading dynos seems to be a point of pride and you have to tolerate a certain amount of dickheadedness now and then when posting on here and dyno figures come up.   Basically add around 10% to anything that comes from an Oz dyno (unless it's a Dynapack) to make it make sense, or subtract 10% from yours (unless it's a Mustang dyno) to avoid dickhead comments ruining the chances of a reasonable conversation when posting on here.

Edited by Lithium

Front diff isn't a weak point in a failure sense, its a weak point in that its an open diff. If you've been around cars long at all you'll know the difference an open vs locked diff can make, so that's why it can be a good upgrade to get an upgraded diff centre in there. Note that you can't do the diff centre swap without taking the sump off, which is an engine out job, which is why a lot of people recommend it straight up instead of a "do it once it becomes a limit" kind of thing. Because at that point you don't want to be engine outing just to do a diff :P

Thank you all very much for the feedback and comments!  I try to save money on labor cost, so for now I focus on upgrades that can be done with engine in.

- Turbos and elbows are first, as I already have full Reimax exhaust.  Is this a job I can attempt by myself with hand tools?  Do the manifolds need to come out?

- Cam gears.  Is there a difference between brands?  I see Tomei cam gears to be quite a bit cheaper than HKS.

- Fuel injectors.  There is a huge price difference for JDM brands, and I am struggling to decide.  A set of Deatschwerks 550cc is $400 USD, but a set of NIsmo 550cc will cost me $650 USD.  Do brands make that much of a difference for injectors?  (I have a Nismo pump installed already)

- ECU.  This is a big road block for me.  I really want to get Haltech, but the only shop in town that tunes Haltech has the worst reputation.  Another shop has wonderful reputation but they strictly do Nistune.  So do I go with a good tuner using old tech or a bad tuner using new tech...?

The issue with dyno numbers is common, and it has more to do with dyno machine brands.  Would be silly if the same car on the same Mustang Dyno produced a different number in the US than in Australia right? (actually would be lower in the US because of the crappy petrol we have)  DynoJet is the most popular brand of dyno here, and the rule of thumb is to take 10-15% off to match a Mustang Dyno.

Edited by TXSquirrel
7 hours ago, TXSquirrel said:

- Turbos and elbows are first, as I already have full Reimax exhaust.  Is this a job I can attempt by myself with hand tools?  Do the manifolds need to come out?

I would imagine the manifolds are simple enough once the turbos have made their way out, good time to port match the outlets to suit your turbos also. 

 

7 hours ago, TXSquirrel said:

- Cam gears.  Is there a difference between brands?  I see Tomei cam gears to be quite a bit cheaper than HKS.

Go with the Tomei, they are proven performers, there were some issues with previous gen HKS cam gears, with weakness in both the gear teeth and the tri-spoke design.

7 hours ago, TXSquirrel said:

- Fuel injectors.  There is a huge price difference for JDM brands, and I am struggling to decide.  A set of Deatschwerks 550cc is $400 USD, but a set of NIsmo 550cc will cost me $650 USD.  Do brands make that much of a difference for injectors?  (I have a Nismo pump installed already)

The Deatschwerks are good units, lots of good feedback in the US, save the 150 for elsewhere.

 

7 hours ago, TXSquirrel said:

- ECU.  This is a big road block for me.  I really want to get Haltech, but the only shop in town that tunes Haltech has the worst reputation.  Another shop has wonderful reputation but they strictly do Nistune.  So do I go with a good tuner using old tech or a bad tuner using new tech...?

Always go with the better tuner over hardware, Nistune is a fantastic option which many workshops in Aus use this ECU, you will save about $1500 on the unit cost alone, which you can utlise elsewhere.  There is some difference under the 4-500hp mark, but not enough to warrant the cost if on a budget.

  • Like 1
8 hours ago, TXSquirrel said:

- ECU.  This is a big road block for me.  I really want to get Haltech, but the only shop in town that tunes Haltech has the worst reputation.  Another shop has wonderful reputation but they strictly do Nistune.  So do I go with a good tuner using old tech or a bad tuner using new tech...?

The issue with dyno numbers is common, and it has more to do with dyno machine brands.  Would be silly if the same car on the same Mustang Dyno produced a different number in the US than in Australia right? (actually would be lower in the US because of the crappy petrol we have)  DynoJet is the most popular brand of dyno here, and the rule of thumb is to take 10-15% off to match a Mustang Dyno.

Considered a Link ECU? 

Australia itself doesn't get worse readings, its just they use Mainline (which probably read closest to Mustang) and Dyno Dynamics (which read a bit lower again) predominantly so as a general rule most of the results end up lower.  American fuel is very comparable with what we get in NZ/Oz - I think there are very few countries which get better than our ~97-98RON (what you guys call ~93).

I was under the impression that all of japan and europe get 100RON aswell :P

 

I'll say this: don't get too hung up on Japanese brands. A few of them make a few good things (tomei oil pump, nismo twin plate) but a lot of them make a lot of overpriced stuff that isn't that great. (injectors, turbos etc :P) Takes a bit of googling to figure it all out but it will pay off in money saved and a superior performance

  • Like 2
2 hours ago, sneakey pete said:

I was under the impression that all of japan and europe get 100RON aswell :P

Pfft they don't count, they don't tend to post on English speaking forums! :P

And yeah sorry was going to add that, very good point - I don't know why people get hung up on Jap brands!

  • Like 1

Look into ECU Master USA. They have plug kits for RBs.

Built in LSU 4.2 controller full sequential injection and ignitor and there will be more workshops available with the knowledge because after all, it's from your country.

And.. if a workshop that says they can tune can't tune a Haltech,  well they should find a new job... 

 

Lastly, Nistune is awesome... it may be "older tech" but what other ECU offers full flex, launch, and boost control for 500$ with change left for hookers and blow? 

Thank you all for the suggestions and comments.  

Hmmm looks like only Haltech and Nistune can work with MAF, all the other ECUs will require running a separate MAP sensor.  I think I am leaning more toward Nistune now.  The local workshop that tunes Nistune is an official authorized dealer, but wow they charge $650 USD for a package, that's a 50% markup.

So a follow up question.  Can the stock narrow crank and oil pump survive the dyno tune?  

Why would you want to keep the air flow meters? They are old now and tend to go faulty fairly often and for the sake of running a vacuum hose its cheap insurance

the short nose crank will be fine as long as you don't limiter bash the engine 

2 hours ago, r32-25t said:

Why would you want to keep the air flow meters? They are old now and tend to go faulty fairly often and for the sake of running a vacuum hose its cheap insurance

the short nose crank will be fine as long as you don't limiter bash the engine 

I want to keep my engine bay looking completely stock, so I plan to keep the stock air box as well.  (yeah stupid I know)  I do plan to upgrade to Z32 MAFs, since they are abundant here and fairly cheap.

I don't think during a dyno tune will get close to limiter.  However I recall reading elsewhere to keep under 6k rpm during dyno to avoid disaster, or is that just a myth?

 

Haltech doesn't use the AFMs, you still need to run a vac feed to the ECU or run an external sensor (which I prefer to do).

There's an option to run the afm, but why would you? I don't think anyone has every bothered to even try that (including myself).

Is there a lot of disadvantages tuning with airflow meter?  Like slow response or inaccurate measurement?  My main goal really is to get good and quick responsive low end, and top end output is just secondary.

I thought Haltech could work on airflow meter without additional vacuum line, at least that's what it reads like on their website.  I guess that leaves me only Nistune.

I have been told at another forum to keep under 6k rpm at all times if I have stock short nose crank, so the thought of a dyno tune really terrified me!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, I started this repair and got as far as "fixing" the holes with some fibreglass. God all those years working on boats came back quickly. I decided I'd reach out to some rust guys just to see what they would say about it. I came across a guy about 40 mins away and went to see him. He said the windscreen needs to come out, that there might be some more bits around the windscreen and he'd quote them at the time. But his quote was $300 to remove and replace windscreen and $3k for the damage he can see. He said he could respray the roof for $1200 and the bonnet for another $800 (somebody has previously rattle canned it, its horrendous). This is $5300 + any small additional bits. It's a lot, I get that and the name of one of my fave youtube channels 'Not Economically Viable' comes to mind.  I'm not being financially rational, but I've taken him up on the quote. He's opening a new shop in November with more room, so we're waiting for that. I'll leave the currently missing headliner out until then. I'm looking forward to it being fixed and having the paint looking nice again (lots of clear coat issues on the roof too). / flame suit on.
    • Oh and some up-and-comings; New rear drivers wheel bearing. I'll do that this weekend while the diff is out. The car is already up and the d/c axles and missing exhaust will help with space. This is the last bearing for me to do and I've been dragging my feet on it. I also have some new EBC blue stuff pads for the car and some new brake fluid. I haven't ever flushed the fluid in this car and looking forward to it. I have 600 degree fluid to put in. Not exactly "race fluid" but better than the typical stuff I have been using.
    • A proper clutch/plate type mechanical diff with quite a lot of pre-load and high locking % is better for drifting. Much more consistent in its behaviour. A helical can be annoyingly vague and inconsistent in how it responds under the sorts of abuse found in drifting.
    • Some updates here. I pulled the entire interior out, minus some trim to respray the seats with Colourlock dye. It turned out really nice though I accidentally let the dog in the car after and she scratched up the front seat.  This is what it looked like before, the colour was just washing out everywhere but thankfully the leather was in good nic. Then after the respray   And after the bloody dog jumped in The headliner is out waiting to be retrimmed, but it will stay out now until Nov - see why below. I replaced the stereo/headunit with a period-styled Android headunit. I have no after pics, but I'll get some. This is because of the missing pixels. I tried to fix this twice with replacement ribbon cables but couldn't. Also the bluetooth interface I'd bought for this was crap. Then there's the rusty roof. Pics and info in this other thread. I have decided to get this repaired professionally, but I'll update that thread. This is why the headliner will stay out for now. I'll be getting the roof and bonnet resprayed at the same time the rust is fixed. I also had an interesting issue with my drivers door lock.  For a small period I was having issues getting any 12v power to the car - I mean *any*. It would have no dash lights, nothing. It happened while I was at the shops and I couldn't get in the car. So, we had 2 problems. The most pressing here is that I was locked out. I have only a single physical key hole on the car, the drivers door and no amount of turning would unlock the car. Surely it doesn't need power for this? The second issue is why am I losing all power periodically, The battery isn't dead, its almost like the battery isn't even there. Two issues that were surprisingly easy to fix. You fellow BMW over-engineering lovers will appreciate this. The lock in the door has 5 states; mechanical lock, electric lock, neutral, electric unlock, mechanical unlock achieved at -90 degrees, -45 degrees, 0 degrees, 45 degrees and 90 degrees. Although, the unlock is towards the front of the car, so opposite for LHD countries. Sticking the key in and turning 45 left or right is what is used 99% of the time. It activates the central locking etc. 90 degrees is for dead battery access and, obvs, only un/locks the one door. But because the mechanical lock is never used and is 27 years old, it seizes up. I was totally unable to turn the key far enough to get to the mechanical unlock (At the time of locking myself out, I didn't even know this was a thing). I eventually did it with some vicegrips and teflon spray.  I made a quick vid for other E39 peeps.   The battery issue is totally new to me also - It wasn't making sufficient contact between the post and the terminal. The terminal was bolted on tight, but the car wouldn't have power. After checking the battery with my multimeter I accidentally contacted the terminal and the battery post and the car got power. The battery was only a few years old and in good condition. I cleaned the post and the terminal with a wire brush, bolted it back on tight and never had the issue again. I'm still surprised that despite having solid contact it didn't work. Also, the car was getting Warragamba sized pools of water in the back when it rained. My initial concern was another rust problem. But when I went out on Weds while it was raining and while I had no headliner in I could see a steady stream of water coming through the roof mounted aerial. As this aerial is for the (now removed) car phone I pulled it out and whacked a blanking grommet in the hole. It seems fine now. I'm thinking I might get the hole permanently filled when the rust is fixed. Moving forward and things in progress; The tailgate needs some attention. I have taken all the trim off to clean it all and address some small rust spots. I have partially done all of this but I'll finish it up hopefully this weekend. As all the trim are now entirely devoid of trim clips I have bought a heap of strong velcro and I'm hoping it does a good enough job as any of this trim in good condition is super expensive and usually in Europe as we dont have many of the wagons here. Suspension and brakes!!! This is exciting. In the front; New control arms New sway bar links New lower Eibach springs (the only modification I'm planning on this car) M Sport shocks (these came with the car and will replace the longer shocks in the car) New top mounts Used 540i calipers (stock brakes suck!) New 540i disks and pads (22x296 mm for 528 and 30x334 mm for 540i) New front wheel bearings (thank all that is holy for bolt on bearings!) Annnnd in the back; New control arms New sway bar links Adjustable air suspension arms (fool the car into what the current height is so the self levelling suspension can match the new front ride height) New ball joints I'll also be doing a brake fluid flush while I'm in there. I'm planning on switching the car over to the 16's that came with it so I can clean up and respray the M Sport 17's. They've lost a lot of colour over the years and have some gutter rash. None of this will start until the E90 is back.
    • You mean you will regret it for drifting duties? I don't quite follow.
×
×
  • Create New...