Jump to content
SAU Community

Recommended Posts

I'm with Terry on this, Camry is the one to get, resale, reliable, roomy, economical, safe ish, adequate power [for its type], low insurance etc etc etc.

Boring as hell, but sometimes even that is a plus. At least you are never disappointed.

only because they are dirt cheap already. the resale on a late model camry is dead set terrible. you can pick up one that is only a few years old for $10,000. the resale is worse than a late model commodore or falcon.

  • Replies 81
  • Created
  • Last Reply

Top Posters In This Topic

im already glad i posted that lol, have suggestions i wouldn't have thought of. does the r31 have abs and airbags? my gf will be driving it a mostly so i'm a bit keen on safety.

how does the 626 go mate? feel and drive alright?

i used to have a 94 camry and thought it was not too bad for what it was, had the shoes replaced in the rear drums one day and the brake balance has been really rear-heavy since lol

get a 31 mate, i was in a similar boat to you, i needed a cheap car that i could drive for a few months b4 i went to england on my gap year and the mrs needed a car to refine her manual driving in and then drive once she got her p's

so i bought a 31, i think i paid $2500 for it

since then its been driven by her for a couple of years, done a couple of trips from qld to tas and its rarely missed a beat

there was a point when it wasn't running but that was due to me fiddeling and taking bits off and not putting them back in right

if you get a 31, just budget for a new dizzy cos its the only thing that goes wrong with them

if she is learning to drive in it then your better off not having abs cos it means she will learn what to do so that she doesn't need abs kicking in cos she slowed down already

its a pretty durable car, they dont really suffer from rust (some have seen rust under the front quarters so check there, but thats about it)

its not great on fuel but its not bad on it either, it get about 10-12l/100km but its soooooooo comfy on the highway

either get a 31 or a really cheap corolla that uses S.F.A. fuel

Get a 5k loan on top of your current 5k and buy an NA liberty. Cheap to run, cheap to service, cheap to insure.

For example: http://www.carsales.com.au/all-cars/privat...5&silo=1011

I just had a service done on my Sti Lib, $119.00.

missus sister had one the model before that. was nice to drive, comfy, went well, nice interior (other than woodgrain). was getting a little bit on in life (160,000kms, so not that old) and started to get some issues. centre diff was going (apparently a semi common problem), and a few other minor issues that were going to be rather expensive to fix (about 2k). the mechanic told her that her best bet was to sell it off and get another car, LOL.

Get a 5k loan on top of your current 5k and buy an NA liberty. Cheap to run, cheap to service, cheap to insure.

For example: http://www.carsales.com.au/all-cars/privat...5&silo=1011

I just had a service done on my Sti Lib, $119.00.

just renewed the insurance on my 31, should have been $270 but went up to $340 cos we changed the address, still cheap tho

the good thing with the 31's is that a new motor is only gonna set you back a few hundred and they don't tend to die (many stories involving motors being pulled down and the factory hone marks are still there!)

would be good if it was better on fuel but i think the handbrake is dragging on ours and the diff is a bit f**ked so it would contribute to increased fuel consumption

if you get a 31, just budget for a new dizzy cos its the only thing that goes wrong with them

if she is learning to drive in it then your better off not having abs cos it means she will learn what to do so that she doesn't need abs kicking in cos she slowed down already

sorry, whats the dizzy?

i have to respectfully disagree with you there, while i agree it is important for all people to know how to stop a car quickly without abs, it is always comforting knowing it is there and there's no doubt that abs reduces chances of an accident

the mechanic told her that her best bet was to sell it off and get another car, LOL.

hahahahaha good mechanic!!

sorry, whats the dizzy?

rascal! :thumbsup:

nah it's the distributor I hazard to guess. bluebirds have the same issue too.

also have you inspected/test driven any of the suggested cars yet?

Edited by jaxt

yeah distributer

after the 20 years the bearing dries up and heats the crank angle sensor up which is in the bottom of the dizzy

not too complicated to do, just set the engine to tdc, pull the leads off the top, pull it out and slot it back in (remembering the orientation)

i know what you mean about abs, its an excellent thing to have and no doubt it has saved many ppl's lives but i think too many ppl rely on it and dont understand what its designed to do and how it does it

but for the sort of money you are thinking of spending i doubt you will get anything with abs and airbags unless its korean and if you want something safe without abs the 31 is about as solid as they come

mine rolled down my driveway cos i didn't pull the handbrake on enough (its an average design and you're best to leave it in gear too) and it rolled into our house, put a small ding into the bricks but left nothing on the car

i also know someone who had the same thing happen but it took out his shed, just went straight through it lol. car was fine, shed was not

if she is learning to drive in it then your better off not having abs cos it means she will learn what to do so that she doesn't need abs kicking in cos she slowed down already

Learning to drive without ABS teaches you the wrong technique for an ABS equipped car in an emergency. If she's likely to be driving a lot of non ABS cars, then it's a handy skill to have. However, if she's only going to drive ABS cars (just about anything made in the last 15-20 years) then knowing how to drive a non ABS car is more likely to cause her to have an accident than knowing what ABS does in an emergency.

When ABS first came out, there wer quite a lot of accidents from people trying to drive them "normally" or even worse panicking when the ABS cuts in and lifting off the brake (because it starts vibrating under the foot)

At the very least, all drivers should get a feel for what ABS does in an emergency, but that's another argument entirely

how about Honda Civic? They are pretty good on fuel and reliable too, especially in your price range, you can get one made in Japan, I reckon the older model is better the new one, like EG.

Corolla is good, but just too many, civic is cool.

  • 1 month later...

just wondering, opinions on a mistubishi magna, 3.0L v6. there's heaps of them with airbags and abs for 3k. missus likes the look (not questioning it) and its cheap and safe.

have a major design project due for final year in a couple of weeks and moving soon after that, then as soon as funds allow will be test driving as much as possible

having owned 2 magnas, i would say go the 3.5L if possible. and if possible get a manual one as they are pretty fast as well (14.8 at willowbank with just a catback exhaust). i had no mechanical problems with mine despite them having a reasonably hard life (especially the first one). only downside to them is the turning circle is pretty shocking, and the front seats really need seat covers as the cover they have from standard is pretty ordinary and a bit coarse.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...