Jump to content
SAU Community

Recommended Posts

let it wear in then try again, you need to slip the clutch to keep the revs up like an auto with a big stall converter does.

I'll give it a crack again sometime... can't be good for her though :miner:

Edited by gwilkinson34
wtf for :D

op - just go buy some MT drag radials, than you wheel spin probs will be gone

Ive heard of lots of dudes using second for launching, more traction etc. Alot of guys actually see quicker 1/4 mile times and 0-100 times launching in second, technique my friend. :miner:

Ive heard of lots of dudes using second for launching, more traction etc. Alot of guys actually see quicker 1/4 mile times and 0-100 times launching in second, technique my friend. :miner:

I think thats only for big power setups, certainly not for a stock turbo!

So, how well do Modded GTR's go here?*

*

1) Sorry for off topic

2) Sorry for not posting in already existing thread

3) I realise turbo choice, launch ability, tyres, and suspension would have MASSIVE effects on this

:P

thanks for the replies guys, new wheels and wider tyres are definately the next step.

Do people think that I will have any tune troubles from where I am (R&R particually) if I was to do the cheap eath boost mod to get 7-8psi all the time?

I was going to do this for the time being until I can put the cash together for a EBC and proper tune

Just want a little more in the mean time :P

if you are interested in 0 to 100 times and only that, you need as much help as you can

ditch the piggy back and stock ecu and get a stand alone, tune it aggressively and run 12psi

but youll need a few other mods for that too, heavy duty clutch, fuel pump, fmic

thats definately the plan longer term, I have already started saving as I want to do it all in one hit so all the supporting mods are there and in place. I was just thinking in the short term.

I think Ill stick with the new sticky tyres and the free boost mod and see what I get out of it, hopefully the computer dosnt crack the sads.

This is the best advice in the thread.

Sell the car.

Buy another R33 that is worth maybe 3-4k more.

You will be getting at least $10-15k worth of mods for that extra $4k, reason is you never get any return on your investment with cars. I did exactly this, bought an R32 gts-t for $11.5k and I got a full rebuilt rb25det, $2k highflow turbo, exhaust, ecu, injectors, suspension, aftermarket ecu, fuel pump, bushes, new clutch etc. Even got the receipts for all the above adding up to over $20k.

Sure sometimes it can be fun building your own car up, personally I think its a stupid waste of money, buy someone else's project and with the ridiculous amount of money you have saved personalise it.

Edited by Rolls

yeah thats true, but I bought this one because it is so clean and tidy. it really is one of the best r33s I have ever seen. even a police offiecer said "Ive pulled over alot of r33s and this si the cleanest one Ive seen" :(

thats the only reason I would stick with it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...