Jump to content
SAU Community

Recommended Posts

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Just grab the usual injector, pump and ECU upgrade and enjoy the power. I assume you have a manifold and know this wont go near bolting up to the std manifold. If you decide its too laggy for you then I have an 8cm housing that will bring it on qbout 300-400rpm earlier that i would be interested in swapping for your 10cm housing

my favourite RB25 turbo setup. I have done about 6 or 7 now. The latest was low mount external gate. 320rwkw on 18psi completely std internals.

You will love it, should be reliable if done correctly.

This is a customers 4door R33 (std internals apart from 260 drop in cams and no vct) 6boost manifold, blitz gate and T67....

post-34927-1278754601_thumb.jpg

my favourite RB25 turbo setup. I have done about 6 or 7 now. The latest was low mount external gate. 320rwkw on 18psi completely std internals.

You will love it, should be reliable if done correctly.

This is a customers 4door R33 (std internals apart from 260 drop in cams and no vct) 6boost manifold, blitz gate and T67....

320kw!

that is massive... i've got 280kw with 17psi

Ill be making a manifold or adaptor myself. What is the boost limt i can run and what power at which psi have you guys seen with this setup? Also where can i get springs for the trust wastegate?

i have a high mount trust manifold here i've been tryin to sell if you want, make me a reasonable offer and its yours.

Just had the car pictured above on the dyno, only change was we fitted a set of Camtech drop in's (http://www.skylinesaustralia.com/forums/Rb20-Rb26-Rb26-Camshaft-t308743.html) Car still has std head and bottom end.

Blue is before cams.

Red is after cams.

post-34927-1278822136_thumb.jpg

Nope, thats why ill get it going on say 7psi now, then buy pump , injectors etc. Any more advice or info to help me along?

dude

seriously u should listen to what ppl are saying, dont just go strap on a large turbo with no supporting mods

a

just do the basic stuff

ecu or piggyback

injectors

nice dump pipe and exhaust mods

and a turbo manifold

fuel pump

then the other stuff later, u will f**k something up by doing it the way u intend on doing it, + the lag that will happen and then only 7psi comes thru might as well leave it stock till u can afford to do it properly

dude

seriously u should listen to what ppl are saying, dont just go strap on a large turbo with no supporting mods

It seems you have missed the OP's topic all together.

He is asking what else is needed once he has this turbo bolted on, and what he can do with it in the meantime. I dont see an issue, chill.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Had I known the diff between R32 and R33 suspension I would have R33 suspension. That ship has sailed so I'm doing my best to replicate a drop spindle without spending $4k on a Billet one.
    • OEM suspension starts to bind as soon as the car gets away from stock height. I locked in the caster and camber before cutting off the kingpin. I then let the upright down in a natural (unbound) state before re-attaching it. Now it moves freely in bump and droop relative to the new ride height. My plan is to add GKTech arms before the car is finished so I can dial camber and caster further. It will be fine. This isn't rocket science. Caster looks good, camber is good, upper arm doesn't cause crazy gain and it is now closer to the stock angle and bump steer checks out. Send it.
    • Pay careful attention to the kinematics of that upper arm. The bloody things don't work properly even on a normal stock height R32. Nissan really screwed the pooch on that one. The fixes have included changing the hole locations on the bracket to change the angle of the inner pivot (which was fairly successful but usually makes it impossible to install or remove the arm without unbolting the bracket from the tower, which sucks) and various swivelling upper arm designs. ALL the swivelling upper arm designs that look like a capital I (with serifs) suck. All of them. Some of them are in fact terribly unsafe. Even the best one of them (the old UAS design) shat itself in short order on my car. The only upper arm that works as advertised and is pretty safe is the GKTech one. But it is high maintenance on a street car. I'm guessing that a 600HP car as (stupidly, IMO) low as you are going is not going to be a regular driver. So the maintenance issues on suspension parts are probably not going to be a problem. But you really must make sure that however your fairly drastically modded suspension ends up, that the upper arms swing through an arc that wants to keep the inner and outer bolts parallel. If the outer end travels through an arc that makes that end's bolt want to skew away from parallel with the inner bolt, you will build up enormous binding and compressing forces in the bushes, chew them out and hate life. The suspension compliance can actually be dominated by the bush binding, not the spring rate! It may be the case that even something like the GKTech arm won't work if your suspension kinematics become too weird, courtesy of all the cut and shut going on. Although you at least say there's no binding now, so maybe you're OK. Seeing as you're in the build phase, you could consider using R33/4 type upper arms (either that actual arm, OEM or aftermarket) or any similar wishbone designed to suit your available space, so alleviate the silliness of the R32 design. Then you can locate your inner pivots to provide the correct kinematics (camber gain on compression, etc).
    • The frontend wouldn't go low enough because the coilover was max low and the upper control arm would collapse into itself and potentially bottom out in the strut tower. I made a brace and cut off the kingpin and then moved the upright down 1.25" and welded. i still have to finish but this gives an idea. Now I can have a normal 3.25" of shock travel and things aren't binding. I'm also dropping the lower arm and tie rod 1.25".
    • Motor and body mockup. Wheel fitment and ride height not set. Last pic shows front ride height after modifying the front uprights to make a 1.25" drop spindle.
×
×
  • Create New...