Jump to content
SAU Community

Recommended Posts

Lads i need some advice, did a bit of searching and didnt come up with much.

R32 Gtr running t04z with all supporting mods

fuel system is 850cc tomei injectors,sard reg,hks twin feed rail, big sx fuel pump with surge tank and gtr standard pump as feed

Now its currently running at 19psi on pump fuel, and i want to get a race fuel tune for an event that is coming up.. i was planning on running e85, and after doing some research have come to the conclusion i will need larger injectors(some say as big as 1600cc!)

so do i go bigger injectors and run e85, if so what injectors should i look at? plan is to push the t04z up to around 26psi.

or do i use something like ERC, VP racing, ELF.. and if so which brand/model do you reccomend..

i wont be doing many events a year with this car, so i dont mind spending a bit on racefuel for a one off each year. also what hp should i expect with 26psi and your choice of fuel?

thanks in advance!

Link to comment
https://www.sau.com.au/forums/topic/332279-which-race-fuel/
Share on other sites

do what i did and do a fuel blend. I went with 50/50 E85/PULP and it works out to be 42.5% ethanol content. very easy to mix since the ratio is simple.

power gains on my car went from 320 rwkw at 20 psi to 360 rwkw at 16 psi plus a load more timing and reponce. i didnt want to upgrade my injectors so this was the best result for me without having to change a single thing! Pretty stoked with it over all!

personally i would go this over some expensive race fuel.

Link to comment
https://www.sau.com.au/forums/topic/332279-which-race-fuel/#findComment-5389845
Share on other sites

Lads i need some advice, did a bit of searching and didnt come up with much.

R32 Gtr running t04z with all supporting mods

fuel system is 850cc tomei injectors,sard reg,hks twin feed rail, big sx fuel pump with surge tank and gtr standard pump as feed

Now its currently running at 19psi on pump fuel, and i want to get a race fuel tune for an event that is coming up.. i was planning on running e85, and after doing some research have come to the conclusion i will need larger injectors(some say as big as 1600cc!)

so do i go bigger injectors and run e85, if so what injectors should i look at? plan is to push the t04z up to around 26psi.

or do i use something like ERC, VP racing, ELF.. and if so which brand/model do you reccomend..

i wont be doing many events a year with this car, so i dont mind spending a bit on racefuel for a one off each year. also what hp should i expect with 26psi and your choice of fuel?

thanks in advance!

[/quot

try some roo 16

Link to comment
https://www.sau.com.au/forums/topic/332279-which-race-fuel/#findComment-5389944
Share on other sites

do what i did and do a fuel blend. I went with 50/50 E85/PULP and it works out to be 42.5% ethanol content. very easy to mix since the ratio is simple.

power gains on my car went from 320 rwkw at 20 psi to 360 rwkw at 16 psi plus a load more timing and reponce. i didnt want to upgrade my injectors so this was the best result for me without having to change a single thing! Pretty stoked with it over all!

personally i would go this over some expensive race fuel.

cheers simon, this sounds like a good alternative. how come you didnt wind it back out to 20psi? injectors maxxing?

Link to comment
https://www.sau.com.au/forums/topic/332279-which-race-fuel/#findComment-5390045
Share on other sites

nytsky 1000cc was going to by initial choice but after speaking to the fella who will be tuning this, he has advised to go with 1400+

Quick rundown on my setup, any holes that need to be filled lads?

standard gtr lift pump

2.5l surge tank

sx fuel pump ( Supports carbureted engines up to 1300 HP and fuel injected engines up to 1000 HP at 45 PSIUltra high-flow rates exceed: 80 GPH at 12 volts and 45 PSI, AND 120 GPH at 12 volts and 10 PSI)

sx filter

-8 teflon from pump to y piece at engine bay.. splitting into two -6 either side of rail

-6 teflon return to sard reg

-6 teflon reg back to surge

injectors are 850cc tomei's.. too small..

what brand injectors? been looking at id2000 and bluemax seem to do some good sizes too.

what would you expect a rb26 t04z at 25-26psi stage 2 hks 272 cams running e85 will make?

Link to comment
https://www.sau.com.au/forums/topic/332279-which-race-fuel/#findComment-5391599
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
×
×
  • Create New...