Jump to content
SAU Community

Recommended Posts

One of my cars that has a dry sump oil system takes for ever to get the oil temps up to the engine operating temperature. The oil system holds about 12+litres of oil as the tank is mounted at the opposite end of the car than the engine, and it uses a -16AN size supply line and a -12 return.

Ive read that nascar use heaters mounted inside their tanks to bring the oil temps up faster when they are pitting the car, but based on what ive researched the heater elements are setup to operate off mains power (110V in the US).

I was thinking about nitrous bottle heaters... and having had no experience with these types of heaters before I figured I'd ask, how hot do these things get, and would it be viable to use a bottle heater to bring the oil temps up faster?

Edited by GTRNUR

We use one of the american heaters for the speedcar dry sump tank. We just have a converter for it. Plug in your regs 240v and it will step down to 110v for the heater pad. Works well!

The lube heaters are the go... but without 'more' plumbing and potential leaks the nitrous bottle heater idea is great.

Once I get back to Tassie, I'll be installing block heaters for lube oil and coolant- for pre start. They are fairly common in colder climate european countries, mercedes has been doing them for years.

The nitrous bottle heaters are just resistantnce heaters in a silicon matt, that are wrapped around the bottle. 12V anything upto 30A. The good one's will be controlled by a pressure switch and realy.

I would be very simple to controll the on/off with a temp switch or ecu output.

Install would be quicker too.

... I like it!

Ha ha

Justin

Sorry Ill be more specific, its a Moroso heater pad to wrap around your dry sump tank. Same as what Justin is referring too.

Sounds similar to a nos bottle heater then.

Ive heard you have to be careful with some of these heaters too, as they can get that hot they tend to burn things they are touching. (though the guy that told me that also sniffs paint, so i'll take that advice carefully). I like the sound of a blanket heater compared to an internal element heater too.

Found the Moroso heater... cheap too.

http://cgi.ebay.com/ebaymotors/NEW-720w-OI...eQ5fCarQ5fParts

I think Ive just worked out why heaters are all 110v. You can only get 300w 12v heaters, so i'd need 4 of them to make a worthwhile heater system. Thats 4 x about 25a current, which would cripple the electrical system pretty well if the heaters were run for the first few minutes of the car running. So that rules out car powered based heating.

Edited by GTRNUR

I can get 240v heaters made to fit up like the moroso element style ones, I can even specify how many watts per inch so it wont burn anything. I get these heaters made all the time to heat water and oil all the time at work. I am actually getting a price on one for a friends drys ump on his 355 holden motor.

I think u would burn the shit out of the oil at that wattage on such a small element, not to mention if you make it you can get the correct fitting to screw into a standard peterson tank etc.

Water boils at 100c and they take what 2 minutes to heat water to this with 1L capacity?

If you are pumping 12L of oil and circulating it you wouldn't burn it.

But you only need it to be on when your in the pits and waiting to go out. Once you start racing for the day, you dont need it again after that. Usually the engine oil will hold its temp for ages. Especially when you have so much of it. Unless your oil cooling system is super good and it keeps your oil cool even during a race then id say you would need it inbetween also.

Yeh you need an external power supply for any of the decent heating pads as I was suggesting in my first post. You just leave the silicon pad attached to your tank with the plug ziptied up somewhere and then you just plug it in when you want to use it. It weighs bugger all too.

Edited by r33_racer

Sounds like mains powered heaters are the go, and I can then wrap the tank in a heat insulation beanie to hold in the heat. I might be able to wire 2 of them in series as my tank is pretty tall, and then wire them direct to 240 instead of using a step down transformer too.

Thanks for the info everyone.

Probably not. The best 12V nos bottle heaters are only 250-300w.

Assuming 100% efficency @ 250-300 watt that is 20-25 amps of current. The 110v heaters are 720watt each, so i'd need 2 -3 heaters to achieve the same level of heating, which equals 60-75 amps of current draw when the heaters are on.

Add that to having to run the rest of the car's ignition, efi etc and it would be overloading the electrical system pretty badly. I think a well insulated tank will do the trick for my application once its up to temp.

  • 1 year later...

After much thought and a much needed break from working on the "other car".... I have had a idea. Its a little out there, but so are some of my other idea's.

Typically the exhaust manifold of a car reaches over 100 degrees inside of 10 second of running, and a front pipe would be well over 400 degrees after about a minute of driving. Some cars use exhaust heat to warm manifolds and provide heat for the car's interior. I figure that while the temps involved are way too high for oil to heat directly, an indirect approach if properly controlled could work.

So here's the idea...

Steam to Oil Heat Exchanger.

Obtain a water-oil heat exchanger from an RB26. Mount it on an external filter style plate, so that there is a means of getting oil in and out of the heat exchanger easily with AN fittings. This unit would then be plumbed into the return line to the tank, before any engine thermostat and coolers.

Exhaust heat coil.

Next, I would get some 3/8" copper tube and wrap it around the front pipe a few time before the CAT (directly after the turbo's). The pipes would then extend up a little and be terminated with braised/silver soldered on AN fittings. The front pipe could then be header insulation wrapped to help keep the heat in.

Coolant resivour.

A small coolant resivour tank would be needed, and would be mounted about the same height as the engine (say near the ABS booster). The tank would hold about 200ml of water, so a greddy style radiator header/air extraction tank would be about perfect, as it has a radiator cap which would help release pressure. It also provides a means of the system replentishing its water supply when it cools down, same principal as a radiator/engines cooling system does due to thermal contraction when cooling.

Electric control of the heat transfer.

An electricly operated solenoid would be connected to the bottom most outlet on the tank as a means of controlling coolant flow. The solenoid would be controlled by a thermal switch to turn it off at 80 degrees oil temp. The solenoid outlet would then be connected to one side of the heater coil around the front pipe. The "out" side of the heater coil would connect to the coolant in side of the heat exchanger, and finally the coolant out side of the heat exchanger returns to the header tank.

Convection steam pumping.

The theory is that when the solenoid is on, gravity feed and convection pumping will provide the flow. The water falls to the heater coil where it will boil virtually instantly. Then as steam builts it will shoot up to the heat exchanger where it will heat the oil, and condense as it returns to the header tank. This is basically the same approach as is used to cool the bearing housings on water cooled turbo's.

I figure that when it is operating the steam temperatures will be pretty extreme, approaching 250 degrees, but this won't burn the oil. Once the solenoid turns off, the heater coil will boil dry eventually and convection pumping will stop. The system will still have some pressure in it maintained by the header tank spring loaded cap, but no pumping will occur anymore.

Since the heater coil and oil heat exchanger are sufficently isolated no more heat will transfer to the oil. The copper will handle the exhaust temps fine as it softens with heat, and will not melt at the peak temps of about 700 degrees that the front pipe occasionally sees.

Does this sound practical and reasonable? Thoughts... opinions.. suggestions? Fire away.

Edited by GTRNUR

good idea but a little complex. having a 240V or even a 110V element or wrap type heater is much easier and certainly proven to work. same as R33 racer the ones i've used had a screw in element in the tank (and used the wrap/blanket type too) and were powered off a step down transformer. the advantage is very little gear in the car (so not much added weight), just the element and it's plug. all the rest of the stuff can live in your garage or be taken with you to any race meets etc. in your climate I imagine you'd only ever need to use it in the morning and the car would be good for the rest of the day even with on/off driving.

the advantage to your system I guess is it's powered by EGT so it's free. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...