Jump to content
SAU Community

Recommended Posts

Hey everyone, just last week I came up to an oportunity and I couldn't resist

So I bought a 1998 r33 gtr :)

Mods

Catback exhaust 3.5inch( need custom dumps for new turbo)

Hks pods

Power fc not installed

I got it pretty cheap so I didn't check it much as long as the bodys straight witch it is because looking to rebuild in the near future,

As being a rb25 boy for 4 years not sure how much the rb26 can take and what would be a good setup.

Any way I took off the front bar , front mount etc to find out heaps and heaps of blow by and stops just after the bovs . So turbo oil seals are gone skies.

So I've got around 5-6 k to spend and buy some goodies :)

Already have power fc with hand controller

I want to keep the twin setup and don't want anything monstrous that will kill my motor or anything.

Hopefully I can reach round the 300kw mark :)

What would the best set up be for my budget?

Some one point me in the right direction !!!

Link to comment
https://www.sau.com.au/forums/topic/334414-just-bought-a-gtr/
Share on other sites

Lots of oil around doesnt mean much TBH. Could simply just be normal blowby, car is 10years old etc, so buildup wouldnt surprise me.

Suspension, full oil changes (diff, transfer case, gearbox etc) service, brakes, PowerFC tune etc IMO.

All belts and the like is where you should spend the money IMO.

Otherwise...

Turbos will be 2500-3000

AFM - 650

Injectors - 800

Labour - 1000

clutch - 1500

So already blown your budget and you still have a car:

1. doesnt handle as well

2. isn't fully reliable by any means of the word.

All of a sudden you've spend near 10k when stuff starts letting go.

Get it all in good condition first, then chase the power.

yeah bro, defiantely start with a nice clean up of the shit first and a catch can. get the pfc in and c where u are from there.

i dont think 300 kw is a good target really in terms of the money u would be spending id be going more for the 380ish mark if u only wanted 300 u should have kept what eva rb25 powered car u had before

As everyone said, if you're not looking at spending huge amount of money, stick with 300awkw as a target. Even that will cost.

The next GTR I get will definitely be one thats got work done or one that is similiar to the N1 (maybe a NUR? hahaha). Cost breakdown as per below (all brand new parts);

1) Catback Exhaust = $1400

2) Dump Pipes = $500 (probably dont have to change if you've got a 34GTR but normally 32/33 will change them when doing turbos)

3) Turbo = $3000

4) ECU = $1400

5) Oil Cooler = $500

6) Clutch = $2500 (I would only like a Nismo Super Coppermix Twin personally but could be way cheaper if you go exedy or npc)

7) Boost Controller = $600

8) Tuning + Installation of ECU/Boost Controller = $1000

9) Metal Hi-Flow Cat = $350

10) Adjustable Coilovers = $1500

11) Labour = $2000

Thats almost $15,000 worth of mods and I would consider these to be basic essential GTR mods for you to enjoy the car's potential. By this time, your car would be very realiable at anywhere between 250awkw-300awkw (depending on your tune etc). If you want dead set 300awkw or slightly above, you'll need fuel system upgrade too and below are some extra cost.

12) Injectors = $1000

13) Fuel Pump = $350

14) Assuming you do not have AFM or else another, AFM = 700

Bare in mind, these will not be the end if you bought a dead stock GTR because you will want to change the rims, brake pads, rotors etc at some stage and the cost just keeps going up. Thats assuming the engine is still running good.

Upgrading the oil pump would be preferred but its a BIG job so not a lot of people would do it. Also if you're doing major service, maybe chuck in the N1 water pump because they've got lesser blades.

Just got it devices with royal pulple 10w-40 k and n oil filter new fuel filter cleaned out all the oily shut in the intake , took the intake manifold off cleaned everything :) I got a cusco catch can not sure how to hook it up my mechanic said don't use that one but I don't see why not? Just the silver one with the blue fitings but hasn't got a breather in it.. Do I need one ?

And another thing the bovs seem fine but it's doesing like a mutherf**ka I Gota look turbo side and see if the recirculating pipe are blocked...

Cheers for all the adivce guys I'll let you know what happins after the tune :P

Keep the discussion going!

i dunno much about the gtrs mate but with the catch can

you want to run the line that goes back to the intake into one side of your catch can then run the other to the intake

so the blow by goes through the catch can on the way to the intake

you can put some steel wool in there too to catch the vapour too (make sure no small bits are gonna come off tho

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...